Hoshizaki KM-470AJ Скачать руководство пользователя страница 3

Страница: 3 / 44

Important Safety Information

Throughout this manual, notices appear to bring your attention to situations which could

result in death, serious injury, damage to the appliance, or damage to property.

WARNING

Indicates a hazardous situation which could result in death or

serious injury.

NOTICE

Indicates a situation which could result in damage to the

appliance or property.

IMPORTANT

Indicates important information about the use and care of the

appliance.

WARNING

The appliance should be destined only to the use for which it has been expressly

conceived. Any other use should be considered improper and therefore dangerous.

The manufacturer cannot be held responsible for injury or damage resulting from

improper, incorrect, and unreasonable use. Failure to service and maintain the

appliance in accordance with this manual will adversely affect safety, performance,

component life, and warranty coverage and may result in costly water damage.

To reduce the risk of death, electric shock, serious injury, or fire, follow basic

precautions including the following:

• Only qualified service technicians should install and service this appliance.

• The appliance must be installed in accordance with applicable national, state, and

local codes and regulations.

• Electrical connection must be hard-wired and must meet national, state, and local

electrical code requirements. Failure to meet these code requirements could result

in death, electric shock, serious injury, fire, or severe damage to equipment.

• The icemaker requires an independent power supply of proper capacity. See the

nameplate for electrical specifications. Failure to use an independent power supply

of proper capacity can result in a tripped breaker, blown fuses, damage to existing

wiring, or component failure. This could lead to heat generation or fire.

• THE ICEMAKER MUST BE GROUNDED.

Failure to properly ground the icemaker

could result in death or serious injury.

• Move the control switch to the "OFF" position and turn off the power supply before

servicing. Lockout/Tagout to prevent the power supply from being turned back on

inadvertently.

• To reduce the risk of electric shock, do not touch the control switch with damp

hands.

• Do not make any alterations to the unit. Alterations could result in electric shock,

injury, fire, or damage to the unit.

• The appliance is not intended for use by persons (including children) with reduced

physical, sensory, or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

Содержание KM-470AJ













































Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды

Hoshizaki KM-470AJ, Руководство по обслуживанию

Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды