Hoshizaki KM-470AJ Скачать руководство пользователя страница 35

Страница: 35 / 44

IV. Refrigeration Circuit and Component Service Information

WARNING

• This appliance should be diagnosed and repaired only by qualified service

personnel to reduce the risk of death, electric shock, serious injury, or fire.

• Move the control switch to the "OFF" position and turn off the power supply. Place

the disconnect in the "OFF" position. Lockout/Tagout to prevent the power supply

from being turned back on inadvertently.

•

CHOKING HAZARD:

Ensure all components, fasteners, and thumbscrews are

securely in place after the icemaker is serviced. Make sure that none have fallen

into the dispenser unit/ice storage bin.

• Make sure all food zones in the icemaker and dispenser unit/ice storage bin are

clean after service.

A. Refrigeration Circuit Service Information

WARNING

• Repairs requiring the refrigeration circuit to be opened must be performed by

properly trained and EPA-certified service personnel.

• Use an electronic leak detector or soap bubbles to check for leaks. Add a trace

of refrigerant to the system (if using an electronic leak detector), and then raise

the pressure using nitrogen gas (0.97MPa). Do not use R-404A as a mixture with

pressurized air for leak testing.

NOTICE

• Always recover the refrigerant and store it in an approved container. Do not

discharge the refrigerant into the atmosphere.

• Do not leave the system open for longer than 15 min. when replacing or servicing

parts. The Polyol Ester (POE) oils used in R-404A applications can absorb

moisture quickly. Therefore it is important to prevent moisture from entering the

system when replacing or servicing parts.

• Always install a new drier every time the sealed refrigeration system is opened.

Do not replace the drier until after all other repair or replacement has been made.

Install the new drier with the arrow on the drier in the direction of the refrigerant

flow.

• When brazing, protect the drier by using a wet cloth to prevent the drier from

overheating. Do not allow the drier to exceed 121°C.

1. Refrigerant Recovery

The icemaker is provided with refrigerant access valves. Using proper refrigerant practices,

recover the refrigerant. Store the refrigerant in an approved container. Do not discharge the

refrigerant into the atmosphere.

Содержание KM-470AJ













































Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды

Hoshizaki KM-470AJ, Руководство по обслуживанию

Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды