Hoshizaki KM-470AJ Скачать руководство пользователя страница 22

Страница: 22 / 44

No Ice Production - Possible Cause

15. Pump Motor

a) Motor winding open.
b) Bearing worn out or locked rotor.
c) Defective capacitor.
d) Mechanical seal worn out.

16. Thermostatic Expansion Valve

a) Bulb loose.
b) Operating erratically.

17. Liquid Line Valve

a) Closed in freeze cycle.
b) Open in harvest cycle.

18. Fan Motor

a) Motor winding open.
b) Bearing worn out or locked rotor.
c) Defective capacitor.

19. Water System

a) Water leaks causing short freeze time.

2. Freeze-Up

Defrost and clean the icemaker prior to diagnosing freeze-up. Fill out a freeze-up checklist.

See "II.I. Freeze Up Check List," or contact your local distributor for a copy of the freeze-up

checklist.

Freeze-Up - Possible Cause

Harvest Cycle

1. Evaporator

a) Scaled up.
b) Damaged.

2. Cube Guides

a) Out of position.
b) Damaged.

3. Spray Tubes and/or Spray

Guides

a) Dirty.
b) Out of position.

4. Water Supply

a) Low water pressure.
b)

External water filters clogged.

Insufficient water line size.

Minimum 1/4" Nominal ID (6 mm Nominal OD in the EU) copper

water tubing or equivalent.

5. Inlet Water Valve

Screen or orifice clogged.

b) Defective.

6. Float Switch

See "II.E. Float Switch Check

and Cleaning"

a) Dirty, sticking.
b) Defective.

7. Refrigerant Charge

a) Low.

8. Control Board

See "III.C. Settings and

Adjustments" and "II.C. Control

Board Check"

a) Harvest timer (S4 dip switch 1 & 2) set too short.
b) Harvest pump timer (S4 dip switch 7) not in factory default position.

c) Defective.

9. Thermistor

See "II.F. Thermistor Check"

a) Loose, disconnected, or defective.

10. Thermostatic Expansion Valve

a) Defective.

11. Hot Gas Valve

a) Closed or restricted.

12. Liquid Line Valve

a) Open.

Содержание KM-470AJ













































Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды

Hoshizaki KM-470AJ, Руководство по обслуживанию

Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды