Hoshizaki KM-470AJ Скачать руководство пользователя страница 10

Страница: 10 / 44

1. Sequence and Component Diagnosis

Power On

: Turn on the power supply, then move the control switch to the "ICE"

position. A 5-sec. delay occurs. CB red "POWER OK" LED and CB green "BC

CLOSED" LED turn on. If CB yellow "BC OPEN" LED is on (indicating a full bin), check

CB K4 red jumper. Move ice away from BC bulb.

Note: • CB red "POWER OK" LED remains on unless the 10.5VAC power supply is

interrupted (K2 connector).

• Check CB using the steps in "II.C. Control Board Check."

•

Confirm CB green "BC CLOSED" LED is on. If CB yellow "BC OPEN" LED is on,

confirm CB K4 jumper is in place. Otherwise, CB yellow "BC OPEN" LED is on

and appliance will not start

Power On Diagnosis:

If CB red "POWER OK" LED is off, confirm 10A fuse is good.

Check for 115VAC at control switch #1 (LBU) to neutral (W) then at control switch

#2 (P) to neutral (W). If 115VAC is present on #1 (LBU) and not on #2 (P), replace

control switch. If 115VAC is present on control switch #2 (P), check for 115VAC at

HPS (P) to neutral (W) then HPS (BK) to neutral (W). If 115VAC is present at HPS

(P) and not at HPS (BK), HPS is open. See HPS Diagnosis below. If 115VAC is

present at HPS (BK), check for 10.5VAC at CB K2 #1 red wire to CB K2 #2 red wire.

If 10.5VAC is not present, check that the cleaning valve is closed and the interlock

switch is closed. Next, check CT continuity. If open, replace CT.

HPS Diagnosis

: Check that the condenser coil is not clogged or restricted. Let

refrigeration circuit pressures equalize. If HPS does not reset and pressures are

equalized, replace HPS. If pressures are not equalized, reclaim refrigerant and

diagnose refrigeration circuit restriction. Check that there are no restrictions in the

refrigeration circuit.

Harvest Cycle: HGV, strainer, or check valve.

Freeze Cycle: FM, TXV, LLV, strainer, check valve, drier, and damaged line set or

fitting.

Confirm that the location meets installation requirements:

• The appliance is not intended for outdoor use. Normal operating ambient

temperature should be within 7°C to 38°C.

• Allow 30 cm clearance at rear, sides, and top for proper air circulation and ease of

maintenance and/or service should they be required.

• The appliance should not be located in a corrosive environment.

Содержание KM-470AJ













































Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды

Hoshizaki KM-470AJ, Руководство по обслуживанию

Результаты поиска

Содержание KM-470AJ

Отзывы:

Похожие инструкции для KM-470AJ

Бренды по названию

Популярные бренды