Horizon Hobby JR DSM 12X Скачать руководство пользователя страница 15

Страница: 15 / 192

I-15

Stick tension adjustments are accessible through covers that

are located on the back of the transmitter (see photo). Carefully

pull back the cover or remove the grip to access the gimbals’

tension screws and then, using a small Phillips screwdriver,

adjust each gimbal’s tension screw for the desired tension

(counterclockwise to loosen stick tension; clockwise to tighten

stick tension).

Advanced Digital Trims

Control Stick Length

Neck Strap Attachment

Control Stick Tension Adjustment

The 12X features Advanced digital trims. On the Normal display

screen, if a trim lever is moved, the screen will automatically

change to display the graphic position for the trim being

adjusted. The 12X Aileron, Elevator and Rudder trim levers and

the right and left side levers feature an audible center trim beep.

This is helpful in determining the trim lever’s center position

during flight. In addition, the frequency of each trim step

changes from full right/up to full left/down, allowing the pilot to

be aware of the general trim position audibly without looking at

the transmitter.

By using the Trim System Function Code 83 located in the

System Mode, the amount of travel per each trim step can be

adjusted as needed to match your specific application.

Please note that when the 12X transmitter is turned off, the trim

values are stored in memory and are recalled when the system

is turned back on.

Use a 2mm Allen wrench to unlock the setscrew to adjust

the stick length. Turn the wrench counterclockwise to loosen

the screw. Then, turn the stick clockwise to shorten or

counterclockwise to lengthen the overall stick length. After the

control stick length has been adjusted to suit your flying style,

tighten the 2mm setscrew. If you desire longer sticks, JR offers

a stick (JRPA047) that is approximately one inch longer than

standard, and has various length anodized aluminum stick ends

available (JRPA040-JRPA045). These stick ends are crafted

from bar stock aluminum, and are available at your local JR

dealer.

An eyelet is provided on the face of the 12X transmitter that

allows you to connect a Neck Strap.

LOOSEN

TIGHTEN

SETSCREW

Содержание JR DSM 12X

































































































































































































Результаты поиска

Содержание JR DSM 12X

Отзывы:

Похожие инструкции для JR DSM 12X

Бренды по названию

Популярные бренды

Horizon Hobby JR DSM 12X, Инструкция и руководство по программированию

Результаты поиска

Содержание JR DSM 12X

Отзывы:

Похожие инструкции для JR DSM 12X

Бренды по названию

Популярные бренды