Horizon Hobby JR DSM 12X Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 192

background image

I-23

Flight Log—Optional for JR R1221 Receiver

Using the Flight Log

Press the button to display the following information:
•  A - Antenna fades on internal antenna A
•  B - Antenna fades on external antenna B
•  L - Antenna fades on the left external antenna
•  R - Antenna fades on the right external antenna
•  F - Frame loss
•  H - Holds

Antenna fades—represents the loss of a bit of information on

that specific antenna.

Typically it’s normal to have as many as 50 to 100 antenna

fades during a flight.

If any single antenna experiences over 500 fades in a single

flight, the antenna should be repositioned in the aircraft to

optimize the RF link.

Frame loss—represents simultaneous antenna fades on all

attached receivers. If the RF link is performing optimally, frame

losses per flight should be less that 20.

Holds are indicated when 45 consecutive (one right after the

other) frame losses occur.

This takes about one second. If a hold occurs during a flight,

it’s important to re-evaluate the system, moving the antennas

to different locations and/or checking to be sure the transmitter

and receivers are all working correctly.

Note

: A servo extension can be used to allow the Flight

Log to more conveniently be plugged in without having to

remove the aircraft’s hatch or canopy. On some models,

the Flight Log can be plugged in, attached and left on

the model using double-sided tape. This is common with

helicopters, mounting the Flight Log conveniently to the

side frame.

The Flight Log is compatible with JR R1221 receivers. The

Flight Log displays overall RF link performance as well as the

individual internal and external receiver link data. Additionally it

displays receiver voltage.

After a flight and before turning off the receiver or transmitter,

plug the Flight Log into the Data port on the JR R1221

receiver. The screen will automatically display voltage i.e.

(6v2= 6.2 volts ).

Note

: When the voltage reaches 4.8 volts or less, the

screen will flash indicating low voltage.

JRPA145

«
...
21
22
23
24
25
...
»

Содержание JR DSM 12X

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JR DSM 12X

Бренд: Value Point Страницы: 7

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Federal Signal Corporation Страницы: 34

Бренд: Quectel Страницы: 95

Бренд: ICAS Страницы: 51

Бренд: Icar Страницы: 40

Бренд: Icar Страницы: 86

Бренд: Icar Страницы: 39

Бренд: IBP Страницы: 12

Бренд: Rachio Страницы: 2

Бренд: Kärcher Страницы: 4

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 7

FT-2000 - MENU MODE LIST

Бренд: Yaesu Страницы: 56

Бренд: Abocom Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды