Horizon Hobby JR DSM 12X Скачать руководство пользователя страница 130

Страница: 130 / 192

H-44

51 thru 58: Programmable Mixers

Programmable mixers are programmed to cause a second

or slave channel to react as a result of providing input to

the primary or master channel or to cause a channel to be

controlled by moving a switch or lever. Programmable mixes

are typically used to activate special aircraft functions like

mixture control, pitch to aileron and elevator mixes to correct

for flight dynamics, etc.

The 12X provides 3 Standard programmable mixes (PROG.

MIX1 - PROG.MIX3) and 5 Multi-Point or Curve programmable

mixes (PROG.MIX4 - PROG.MIX8). Multi-Point (or Curve)

mixing provides the ability to program a customized curve that

the slave channel will follow as it reacts to the master channel’s

input. Multi-Point mixes are different from normal mixes in that

normal mixing results in a linear movement of the slave channel

in relation to the master. With Multi-Point mixing there are up

to 8 points that can be adjusted to control the position of the

slave channel providing the ability to custom tailor the output of

the slave channel.

The primary channel is called the master channel, while the

channel that reacts to the master is called the slave channel.

Mixes are fully programmable, allowing any of the 12 channels

to be master, slave or both (a channel can be mixed to itself).

Trimmers and levers can also be used as a master and are

extremely useful for programming proportional channels to

be operated via a trimmer or lever. Additionally programmable

mixes can always be on or turned off and on via a programmed

switch, Stick position or flight mode. The Snap Roll/ Trainer

switch (momentary switch SNPT) can also be programmed as

the master channel.

Additionally there are 2 options for Master channels:

“#” (pound sign), these master channels are origin-type mixes.

These include #THRO #AIL, #ELE and #RUD. Origin mixing

bypasses any other mixing that might affect that channel

such as throttle curves, exponential, travel adjust or other

programming and uses the stick position only to control the

mix.

“+” sign, these master channels are trim-include-type mixes.

These include THR+, ELE+, AIL+ and RUD+. Trim-include mixes

include the trim of the master channel as well as any other

mixing to the master channel to control the slave channel of the

mix.

The 12X has 3 standard programmable mixers that allow for

linear mixing of a master channel to a slave channel. The

standard mixers are PROG.Mix1, Mix 2 and Mix 3.

These mixes provide for 2 sets of mixing values named Pos0

and Pos1. If one set of values is set to 0% then the mixer can

be turned on and off with a stick, switch or lever. Each set of

mixing values is comprised of 2 percentages to accommodate

movement of the master channel in both directions. This is

shown in the illustration below where there is an upper and

lower percentage for both Pos0 and Pos1.

A mix can be made to always be on by setting Pos0 values only

and not selecting any switches to switch between the Pos0 and

Pos1 values.

Standard Programmable Mixer - (Std. Prog Mixer)

Содержание JR DSM 12X

































































































































































































Результаты поиска

Содержание JR DSM 12X

Отзывы:

Похожие инструкции для JR DSM 12X

Бренды по названию

Популярные бренды

Horizon Hobby JR DSM 12X, Инструкция и руководство по программированию

Результаты поиска

Содержание JR DSM 12X

Отзывы:

Похожие инструкции для JR DSM 12X

Бренды по названию

Популярные бренды