Horizon Hobby JR DSM 12X Скачать руководство пользователя страница 60

Страница: 60 / 192

A-34

Programmable throttle curves allow the throttle response (stick

position vs. throttle output) to be manipulated. This is useful to

optimize the throttle response for various maneuvers like torque

rolls. Programmable throttle curves can be adjusted with the

THRO CURV function. Two programmable throttle curves are

available.

If the Twin E. function has been activated in Wing Type (page

A-27 for twin-engine aircraft, independent throttle curves are

available for each engine to help eliminate discrepancies in rpm

between the two engines at all throttle positions.

18: Throttle Curves

1. Highlight and select THRO CURV in the FUNC.LIST. and

press YES or NO to access the throttle curve function. Two

different throttle curves can be programmed referenced to

as Pos0 and Pos1.

2. If there is a need to have 2 throttle curves, use the Selector

to highlight SW SELECT and a list of available Flight

Modes and switches appears. Select the Flight Mode(s)

(FM0, FM1, or FM2), switches and/or switch position

(SPS) that is desired to be used to select between the 2

curves. The switch will be used to select between the Pos0

curve and the Pos1 curve. Highlight and select Pos0 to

toggle between the Pos0 and Pos1, in order to display and

adjust the 2 curves.

Note

: If Twin E. has been activated for a twin engine

aircraft, there will be a Pos0 and Pos1 for both the right

and left engines, providing a total of 4 possible throttle

curves. However, instead of being named Pos0 & Pos1,

they are named RTH.0, RTH.1, LTH.0, and LTH.1. They

represent Right Throttle Pos0 & Pos1 and Left Throttle

Pos0 & Pos1 respectively.

3. Highlight EXP and select it to turn exponential ON if

desired. This will result in a smoothed throttle curve.

4. Using the roller, highlight the desired point (L, 1, or H) and

press the roller to access the output value. Rotate the roller

to change the output value. Repeat for all desired points.

Note the graphic display will change to represent the new

point position.

5. To adjust access Pos1 throttle curve (only available when

SW is assigned to a switch) highlight Pos0 and rotate the

roller to access Pos1 and repeat the step above to adjust

Pos1 throttle curve.

6. To adjust the throttle trim authority, highlight the TRIM

using the roller and rotate to select a trim authority value of

0 100%. Note the graphic display will change to represent

the new trim authority.

7. To store a new point move the throttle stick until store

appears on the lower left side of the screen. When the

desired position is achieved press the store button and the

point will be stored onscreen. Up to eight points can be

stored.

9. THRO STK allows the throttle stick to be used to switch

from Pos0 throttle curve to Pos1 throttle curve. To program

a throttle curve Pos change with the throttle stick highlight

the THRO STK and adjust the values using the roller to

program the point at which the throttle curve is selected

between Pos0 and Pos1.

To Program a Throttle Curve

Содержание JR DSM 12X

































































































































































































Результаты поиска

Содержание JR DSM 12X

Отзывы:

Похожие инструкции для JR DSM 12X

Бренды по названию

Популярные бренды

Horizon Hobby JR DSM 12X, Инструкция и руководство по программированию

Результаты поиска

Содержание JR DSM 12X

Отзывы:

Похожие инструкции для JR DSM 12X

Бренды по названию

Популярные бренды