Horizon Hobby JR DSM 12X Скачать руководство пользователя страница 186

Страница: 186 / 192

S-46

87: Timer

The 12X features a sophisticated Timer System with three

timers. An integrated timer keeps track of total Tx-on time for

the current selected model and integrated time is displayed

on the Main display. Two other timers can be configured as

Countdown timers or as a Stopwatch. These timers also appear

on the Main display when active and can be started and stopped

via various switches. In addition, an interval function can be

programmed such that alarm will sound at preprogrammed

intervals. A Down Alarm can be programmed that will sound an

alarm prior and up to the programmed countdown time and a

one-time function sounds the alarm once or continuously when

the time is reached.

2. To Reset the Integrated Timer, highlight and select the

time under INTEG-T and Push [CLR]=0:00 appears on the

display. Press the CLR button to the left of the display to

reset the integrated timer.

3. To reset the Stop Watch or Countdown Timer, highlight the

timer function using the roller on the screen and press CLR.

1. To configure the timers, highlight and select Timer in the

FUNCTION LIST to obtain the Timer display.

Highlight and select INH under TIMER1 or TIMER2 and

then select DOWN-T of STOP W. Use the Selector to set

the countdown set time, interval, down alarm and one-time

functions. Once the timer is set, TIM will appear on the Main

display in the lower left corner. The timers can be programmed

to several different buttons or switches. Use the Selector to

highlight the desired button or switch to operate the timer. Press

the Selector to confirm the selection. The desired set time, beep

interval, down alarm can be set as desired. When the One-Time

function is ON, the timer will start with the switch selected, but

pressing the switch again will have no effect. If the One-Time

function is OFF, the timer can be stopped, and restarted as

many times as desired with the switch selected.

Содержание JR DSM 12X

































































































































































































Результаты поиска

Содержание JR DSM 12X

Отзывы:

Похожие инструкции для JR DSM 12X

Бренды по названию

Популярные бренды

Horizon Hobby JR DSM 12X, Инструкция и руководство по программированию

Результаты поиска

Содержание JR DSM 12X

Отзывы:

Похожие инструкции для JR DSM 12X

Бренды по названию

Популярные бренды