Horizon Hobby JR DSM 12X Скачать руководство пользователя страница 61

Страница: 61 / 192

A-35

The 12X provides the ability to adjust the speed of servos on

each channel in each direction. The speed may be reduced

(servo slowed) from its normal speed but it cannot cause a

servo to move faster than its rated specifications. Each servo

can have 2 sets of speeds in each direction that are Flight Mode

or switch selectable.

The servo speed function can be very useful for scale models

with retractable landing gear and gear doors, since in many

instances the need for gear door sequencers can be eliminated.

If the gear door servos move at normal speed and the landing

gear servos move at a slower speed when the gear is lowered,

the gear doors will be open before the landing gear begins to

come down. In the opposite direction, if the gear door servos

move slowly and the landing gear servos move at normal

speed, the gear can retract before the gear doors begin to close.

Note

: Many retract servos are non-proportional type

servos that simply move from end point to end point.

These types of servos are not adjustable in the servo

speed function.

24: Servo Speed

1. Highlight and select SRV. Speed. Speed FUNC.LIST.
2. Select SW SEL and press the roller to access Switch Select.

If only one servo speed is desired, then all selectable switch

positions in this screen should be P0. If two servo speeds

are desired, then assign the desired switch that will change

the servo speed to P1. Return to the main screen.

3. If a single set of servo speeds is desired, make sure the

display is showing Pos0. If it is not, select Pos1 and

change it to Pos0. Highlight and select the channel and

direction for each servo that is to be adjusted. Once a

direction for a servo is selected, the servo speed may be set

so the servo travels from .193 seconds for 60 degrees of

rotation to 16.4 seconds for 60 degrees of rotation. Adjust

the speed of each servo until the desired speed is obtained.

4. If 2 sets of servo speeds are desired that are Flight Mode

or switch selectable, one set of values is set to NORM for

all channels, and the slowing of servos can be turned off by

selecting the position (Pos0 or Pos1) that has the NORM

values. Highlight and select Pos0 and change it to Pos1

and then highlight and select the channel and direction for

each servo that is to be adjusted. Once a direction for a

servo is selected, the servo speed may be set so the servo

travels at the desired slower rate. Switch between Pos0 and

Pos1 to view and adjust the 2 sets of values for each servo.

Note

: Pos1 always has priority over Pos0. In other words,

if multiple switches are selected and one of the switches

is in its Pos1 position, then all other switches are ignored

and the Pos1 values are in effect.

To Adjust Servo Speed

Содержание JR DSM 12X

































































































































































































Результаты поиска

Содержание JR DSM 12X

Отзывы:

Похожие инструкции для JR DSM 12X

Бренды по названию

Популярные бренды

Horizon Hobby JR DSM 12X, Инструкция и руководство по программированию

Результаты поиска

Содержание JR DSM 12X

Отзывы:

Похожие инструкции для JR DSM 12X

Бренды по названию

Популярные бренды