horiba HU-200TB-W SS-120-W, Инструкция по эксплуатации

Страница: 43 / 109

Operation
31
F.dt
FAiL output delay time
setting Specify the time in seconds from when a FAiL
occurs until a contact is output.
0 to 600 (s) 0 43
Curr General transmission output setting 43
C.HoLd
Transmission hold plan in
general Specify the transmission holding status in
general in the output hold mode.
HoLd, PrES HoLd 43
b.out
Burnout hold setting for
general transmission
output
Specify the burnout current of the transmission
output when an error occurs during
measurement.
Note:
A burnout current is output in the meas mode
only.
non, out.4,
out.20
non 44
Cur2.t
Transmission output 2
range (fixed/automatic
changeover) setting
For transmission output 2, a maximum of four
ranges can be switched using the external
contact. In addition, the converter selects the
optimal range according to the automatic range
changeover function.
rng, Auto rng 44
Cur1 Transmission output 1 setting 44
C.rng
Transmission output 1 full-
scale range (fixed range)
setting Select the transmission output range. The
alarm value can be specified based on the
selected decimal point.
10.00,
100.0, 1000
100.0 44
rng.0
Zero point value setting for
transmission output 1
Specify the value at the zero point (4 mA)
of transmission output 1.
Note:
The item of sub display depends on which
ever “10.00”
*1
, “100.0”
*2
or “1000”
*3
in
“C.tgt” of Cur1 is selected.
*1
0.00 to
11.00
0.00
44
*2 0.0 to 110.0 0.0
*3 0 to 2200 0
rng.S
Span point value setting for
transmission output 1
Specify the value at the span point (20 mA)
of transmission output 1.
Note:
The item of sub display depends on which
ever “10.00”
*1
, “100.0”
*2
or “1000”
*3
in
“C.tgt” of Cur1 is selected.
*1
0.00 to
11.00
10.00
44
*2 0.0 to 110.0 100.0
*3 0 to 2200 1000
PrES
Preset value setting for
transmission output 1
Input the preset value for current holding.
Note:
This is displayed when “C.HoLd” is set to
“PrES” and the item of sub display
depends on which ever “10.00”
*1
, “100.0”
*2
or “1000”
*3
in “C.rng” of Cur1 is selected.
*1
0.00 to
11.00
10.00
44
*2 0.0 to 110.0 100.0
*3 0 to 2200 1000
Cur2.A to
Cur2.d
Transmission output 2.A to 2.d setting
Tip

The other transmission output 2.b, 2.c, 2.d can be set in the same manner.

The transmission output 2 provides maximum four output ranges which are selected
by external inputs or automatic range selection function. The zero and span point of
the transmission range can be set any within the measuring range.
44
C.rng
Transmission output 2.A
value (full-scale range)
setting
Select the transmission output
range. The alarm value can be
specified based on the selected
decimal point. Cur2.A
10.00,
100.0, 1000
1000
44
Cur2.b/2.c 100.0
Cur2.d 10.00
Display Item Description
Setting
range
Initial
value
Refer
to page