Honeywell HTRD400 Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 176

Honeywell HTRD400 Скачать руководство пользователя страница 149

Rev 1.02

135

Document 900.0328

05/05

D

Solutions

This appendix provides possible solutions for resolving system malfunctions that may
occur from time to time. It also describes common error and warning messages
generated by the Toolbox and Player applications.

Troubleshooting

If this happens …

Try this …

You have lost your password and
cannot connect to the HTRD400
Recorder.

If the default factory-set password has been changed and is subsequently
lost, contact Honeywell Technical Support. See

Warranty and Service

for contact information.

You cannot see a recorder in the
recorders list

OR

The connected PC or laptop does
not recognize the HTRD400
Recorder.

Check:

•

That the HTRD400 Recorder is powered up

•

The physical connections between your PC and the HTRD400 Recorder
unit

•

Ensure that a CAT5 Ethernet crossover cable is used to connect your
PC and the HTRD400 Recorder.

•

Your IP address. Ask your IP network administrator for assistance.

See

for more information.

The Record LED is flashing and
video is not recording.

Check if:

•

The hard drive is full. To clear the hard drive, see

Modifying Recorder

.

•

The HTRD400 Recorder has been set to Stop mode. Reset recording

mode to Recycle (see

Configuring Recorder Global Settings

archive video files to your PC (see

Archiving Clips and Images

), and then erase the hard drive (see

Configuring Recorder Global

).

The Temperature LED is flashing.

The temperature is outside the operating temperature range. Normal
operation resumes as soon as the operating temperature range is reached.

The Fault LED is on.

The HTRD400 Recorder has detected a problem. Reset the unit by
disconnecting the power and reconnecting. If the problem persists, contact
Honeywell Technical Support.

«
...
147
148
149
150
151
...
»

Содержание HTRD400

















































































































































































Отзывы:

Нет отзывов