7 Channel 2.4 GHz Aircraft Computer Radio System
7 Channel 2.4 GHz Aircraft Computer Radio System
Section 5: Acro and Glider Programming Menu
Section 5: Acro and Glider Programming Menu
66
67
Aile>Rudd
c. If you choose “Cond” (Flight Condition):
- The upper right field of the menu displays which flight
condition is currently active and will be programmed.
- Scroll to the Flight Condition field and press the jog dial to
activate the menu.
- Choose the desired flight condition and press the jog dial to confirm your selection.
- Repeat steps 4-12 to define the settings for each flight condition.
15. Press the back button to return to the model function menu.
To disable the aileron-rudder mix:
1. Scroll to highlight the “MIX” field in the aileron-rudder mix
menu and press the jog dial to activate the menu.
2. Select “INH” (inhibit) and press the jog dial to confirm your
selection.
3. Press the back button to return to the model function menu.
You may also select a flight condition in this menu by activating the desired flight condition.
Note
Tip
Tip
Tip
Caution
Elev>Camb
The Elevator-to-Camber Mix allows the model to drop and raise the trailing edge of the wing control
surfaces in conjunction with elevator inputs. This function is not valid for the “1AILE” or “ELEVON” wing
types unless flaps are also present. If using a “1AILE + 1FLAP”, “1AILE + 2FLAP”, “ 1FLP”, or
“ 2FLP” wing type, do not configure any settings for the “AILE” function. Configure only flap
servo movements.
To configure an elevator-to-camber mix:
1. From the model menu, rotate the jog dial to highlight
“ELEV>CAMB” and press the jog dial once to enter the
activation menu.
4. Scroll to the function field (“AILE” or “FLAP”). If “AILE” is not
the current function, press the jog dial to activate the menu.
Otherwise, skip to step.
5. Scroll to select “AILE” and press the jog dial to confirm your
selection.
2. Press the jog dial again to activate the menu.
3. Rotate the jog dial to select “ACT” (activate), then press the jog
dial to confirm your selection and activate the elevator-
camber mix menu.
Elev>Camb cont.
7. Scroll to the top row of the value table (“AILE”) and press the
jog dial to activate the menu.
8. Scroll to highlight the “L/U” (left/up) field and press the jog dial
to activate the menu.
9. Rotate the jog dial to set the desired endpoint for the servo
attached to the “AILE” receiver slot. This value regards the servo
travel when a pitch up command is given. This setting does
not affect the travel of the servo when roll commands are
given. Press the jog dial to confirm your input.
10. Scroll to highlight the “R/D” (right/down) field and press the
jog dial to activate the menu.
11. Rotate the jog dial to set the desired servo endpoint for the
when a pitch down command is given.
13. Scroll to highlight the “EXP” field and press the jog dial to
activate the selection.
14. Rotate the jog dial to input the desired exponential travel of
the aileron servos when reacting to this mix. The setting does
not affect exponential travel of the servos when roll
commands are given.
12. Repeat steps 6-10 to set the endpoints for the servo attached to the “AIL2” receiver slot (second row of
the value table). As with the previous settings, the values input here do not affect the servo travel
when roll commands are given.
15. Scroll to highlight the “TRIM” field and press the jog dial to
activate the menu.
16. Scroll to select “ON” or “OFF” and press the jog dial to confirm
your selection. When “ON” is selected, the mix reacts to trim
adjustments of the elevator. Otherwise, the mix ignores
elevator trim changes.
17. If the model is equipped with flaps, scroll to the function field
(“AILE” or “FLAP”) and press the jog dial to activate the menu.
Otherwise, skip to step 19.
Содержание Flash7
Страница 1: ......