7 Channel 2.4 GHz Aircraft Computer Radio System
Section 5: Acro and Glider Programming Menu
57
7 Channel 2.4 GHz Aircraft Computer Radio System
Section 4: Common Model Programming Menu
56
Monitor cont.
Throttle Lock
3. Press the jog dial to activate the test menu.
4. Scroll to highlight “Move” and press the jog dial to confirm
your selection.
5. Observe as the transmitter cycles the designated range of
travel for every channel that has been assigned a control
input.
6. The cycle test can be halted by either selecting another option
in the test menu or pressing the back button to return to the
model function menu.
7. Scroll to highlight “NEU” (neutral) and press the jog dial to
confirm your selection.
1. To turn the throttle lock highlight THRO Lock from the model
setup menu and press the jog dial to enter the setup screen.
8. Observe that all channels with assigned control inputs have been set to their neutral position
(including all trim or sub-trim settings). This screen is useful to position the servos when setting
pushrod lengths for control surfaces.
9. The neutral setting can be halted by either selecting another option in the test menu or pressing the
back button to return to the model function menu.
The Flash 7 features a “throttle lock” function that can be activated when the transmitter is transmitting
a signal. We encourage you to use the throttle lock feature as a safety precaution against “accidental
throttle application”.
Acro and Glider Programming Menu
When the active model is configured as a fixed-wing (ACRO or GLID) model type, the Model Function
menu contains programming options which are useful for fixed-wing aircraft. This section describes the
features and programming steps for the ACRO and GLID model function menus.
From the Model Function menu, you can program the following fixed-wing-specific functions:
FLT.COND:
Configure specific control settings for different phases of flight.
AIL DIFF:
Configure aileron servos to move further upwards than down.
ELEVON MIX:
Specify independent pitch and roll control throws for aircraft with elevons.
V-TAIL MIX:
Specify independent pitch and yaw control throws for aircraft with a V-tail.
AILEVATOR:
Specify independent pitch and roll control throws for aircraft with ailevators (also called
“tailerons”).
AIL>RUD:
User-adjustable mix that defines rudder movement with aileron control inputs.
ELEV>CAMB:
Alter wing control surfaces with elevator inputs.
Camber Mix (GLID only):
Adjust wing control surfaces with switch movements.
FLAP CON:
Mix elevator throw with flap movement.
OFFSET:
Fine tune aileron, elevator, and flap positions.
B-fly (GLID only):
Configure wing control surfaces to act as an air brake (also known as “crow”).
GYRO:
Specify gyro on/off and sensitivity settings.
THRO CUT (ACRO only):
Configure a kill switch for glow/gas motors.
T.CURVE (ACRO only):
Specify non-linear throttle response.
If you have not already programmed a model with the preceding quick start guide, we
encourage you to do so before tackling the model programming section of the manual.
Warning
Note
Tip
Tip
Tip
Caution
ACRO Model Function Menu Page 1
ACRO Model Function Menu Page 2
Glider Model Function Menu Page 1
Glider Model Function Menu Page 2
2. To select which switch will be used for the throttle lock press
the jog dial to enter the switch selection menu.
3. Scroll to select a switch used to activate the throttle lock
function. Press the jog dial to confi rm your selection.
- If you choose the “NULL” option, the function will remain
inactive at all times for this model.
However, for user convenience, Throttle Lock can be activated/
4. Press the back button twice to return to the Model menu.
- If you choose a switch:
- The switch position menu will appear. Scroll to high light
the switch position that you will use to enable the function. Press the jog dial to confi rm your selection.
- Scroll to select “ON” and press the jog dial to confi rm your selection. If you toggle the selected
switch, the fi eld in the top right corner of the screen will indicate when the mix is active.
inactivated by press and hold ESC button 2sec on the main menu despite choose ‘NULL option.
Содержание Flash7
Страница 1: ......