Hill-Rom WatchCare Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 74

Hill-Rom WatchCare Series Скачать руководство пользователя страница 19

WatchCare™ Incontinence Management System User and Service Manual (196414 REV 2)

13

Cleaning and Disinfecting

CLEANING AND DISINFECTING

NOTE:

This section does not apply to the smart pads. The smart pads are
intended for single use only. Discard a soiled smart pad at least 2 feet (61
cm) from the bed so that the reader no longer detects the soiled pad.

WARNING:

To help prevent injury and/or equipment damage, obey these

warnings

:

•

Warning

—The potential for electrical shock exists with electrical

equipment. Failure to follow facility protocol could cause death
or serious injury.

•

Warning

—Do not reuse wiping material for multiple steps or on

multiple products.

•

Warning

—Harmful cleaning solutions may cause skin rash

and/or irritation upon contact. Follow the manufacturer’s
instructions found on the product label and Safety Data Sheet
(SDS).

•

Warning

—Lift and move items correctly. Do not twist, and seek

assistance when necessary. Make sure the bed is at a correct
height to lift items off the bed.

•

Warning

—Fluid spills on to the system’s electronics could cause

a hazard. If such a spill occurs, unplug the bed and remove it from
service. When fluid spills occur outside of what is seen in normal
use, immediately do as follows:

a.

Unplug the bed from its power source.

b.

Remove the patient from the bed.

c.

Clean the fluid spill from the system.

d.

Have maintenance examine the system completely.

e.

Do not use the system until it is completely dry, tested, and
found to be safe to operate.

DRAFT 26-FEB-2019

«
...
17
18
19
20
21
...
»

Содержание WatchCare Series











































































Отзывы:

Нет отзывов