Hill-Rom WatchCare Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 74

Hill-Rom WatchCare Series Скачать руководство пользователя страница 18

WatchCare™ Incontinence Management System User and Service Manual (196414 REV 2)
12

Transport The Bed

Replace the WatchCare™ smart pad

The indicator light will flash amber to indicate an incontinence event. If
you are using a nurse call system, customizable incontinence alerts can be
sent to—

•

The nurse call console

•

The nurse call dome light over the door, outside the patient’s
room

•

The applicable mobile devices available at your facility

•

The nurse call status board

1.

Remove the soiled smart pad(s), and discard the pad(s) at least 2 feet
(61 cm) from the bed so that the reader no longer detects the soiled
pad(s).

2.

Put a new smart pad on the bed, and listen for the single beep to
make sure the new pad is being monitored.

•

If there is no beep, look at the indicator light. If the light is white,
the smart pad is not detected. Make sure the pad is in the correct
head/foot orientation and intended location (see Step 3 on page
11).

•

If you are using more than one smart pad, make sure the
indicator light is green after the soiled pad is removed.

NOTE:

When the new pad is detected, the alert will clear in the WatchCare™
System.

TRANSPORT THE BED

1.

Prepare the bed for transport per the bed’s user manual.

2.

Disconnect the bed cable (WatchCare™ 1/4"communication cable,
SideCom® cable, or WatchCare™ adapter cable) from the equipment
call jack on the wall.

3.

Transport the bed per facility protocol.

4.

After the transport, do these:

a.

Plug in the bed’s power cord.

b.

Connect the bed cable (WatchCare™ 1/4" communication cable,
SideCom® cable, or WatchCare™ adapter cable) to the equipment
call jack on the wall.

DRAFT 26-FEB-2019

«
...
16
17
18
19
20
...
»

Содержание WatchCare Series











































































Отзывы:

Нет отзывов