manualshive.com logo in svg

Hill-Rom P870, Руководство пользователя

Поделиться
Скачать
Hill-Rom P870 Скачать руководство пользователя страница 137

4.8  Optional Siderail Control Panels

Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 30

Resident

TM

 LTC Bed Service Manual (man136rc)

4

f.

Position the head/knee P.C. board to the inner housing (G), and secure 
it with the four phillips head screws (E). Use care when tightening the 
mounting screws to prevent damage to the P.C. board.

CAUTION:

Overtightening the mounting screws can crack the P.C. board.

8. If the hilow P.C. board is to be replaced, proceed as follows:

a. Carefully remove the four phillips head screws (D) securing the hilow 

P.C. board (C) to the outer housing (R).

b. Slide the cable connector (Q) from the hilow P.C. board, and remove 

the hilow P.C. board (C).

c. Connect the cable connector (Q) leading from the head/knee P.C. board 

(F) to its terminal on the replacement hilow P.C. board (C).

d. Position the hilow P.C. board (C) to the outer housing (R), and secure it 

with the four phillips head screws (D). Use care when tightening the 
mounting screws to prevent damage to the P.C. board.

CAUTION:

Overtightening the mounting screws can crack the P.C. board.

Replacement

1. Assemble in reverse order. Replace the siderail labels (A and I) if 

damaged.

2. Ensure that the connected control cable is properly routed along the main 

frame and connected to the control lockout box.

3. Install the cable ties to secure the control cable where it will not be 

damaged during bed operation.

4. Perform an operational check of the hilow, head, and knee functions. See 

“Function Checks—Electric Drive Model” on page 2-10.

Содержание P870








































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды