manualshive.com logo in svg

Hill-Rom P870, Руководство пользователя

Поделиться
Скачать
Hill-Rom P870 Скачать руководство пользователя страница 132

4.7  Automatic Contour Module

Chapter 4: Removal, Replacement, and Adjustment Procedures

Resident

TM

 LTC Bed Service Manual (man136rc)

Page 4 - 25

4

Adjustment

1. With the automatic contour module installed on the bed and its cover 

removed, plug the bed into an appropriate power source.

2. Press the HEAD Up button to raise the head. Check the head angle 

indicator decals (located at both sides of the bed on the sleep surface) to 
observe the degree at which the knee section stops rising. This should be 
approximately 15

o

. Continue to raise the head section until clearance exists 

between the sleep surface crosstube and the plunger at the head end side of 
the automatic contour module. 

3. Press the HEAD Down button to lower the head section. Check the head 

angle degree at which the knee section begins to lower. This should be 
approximately 15

o

. Continue to lower the head and knee sections to the flat 

position.

4. If adjustment is necessary:

a. Loosen, do not remove, the two screws (A) securing the automatic 

contour module to the weldment bracket (see figure 4-20 on page 
4-25).

Figure 4-20.  Automatic Contour Module—Cover Removed

A

A

m136_067

Содержание P870








































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды