manualshive.com logo in svg

Hill-Rom P870, Руководство пользователя

Поделиться
Скачать
Hill-Rom P870 Скачать руководство пользователя страница 136

4.8  Optional Siderail Control Panels

Chapter 4: Removal, Replacement, and Adjustment Procedures

Resident

TM

 LTC Bed Service Manual (man136rc)

Page 4 - 29

4

c. Clip the cable wires approximately 1" (2.54 cm) from the connector 

(K). Slide this connector from the P.C. board. Use the color-coded 
wires as a guide when connecting the new cable to the connector.

d. Pull the siderail control cable (N) free of the siderail.

e. Insert the new cable through the spring (L) installed in the siderail. 

Route it up the siderail arm, through the bushing, and through the 
cutout in the bottom of the siderail.

f.

Connect the new cable to the connector using the color-coded wires in 
the removed connector as a guide for proper connections (see “Siderail 
Control Schematic” on page 3-4).

g. Slide the cable connector (K) onto the P.C. board. 

h. Position the head/knee P.C. board (F) to the inner housing (G), and 

secure it with the four phillips head screws (E). Use care when 
tightening the mounting screws to prevent damage to the P.C. board.

CAUTION:

Overtightening the mounting screws can crack the P.C. board.

i.

While ensuring that control cable (N) is centered inside the wire cover 
(M), maneuver the cover into position on the siderail pivot arm (O).

j.

Install the two torx head screws (P) to secure the wire cover to the 
siderail pivot arm.

7. If the head/knee P.C. board (F) is to be replaced, proceed as follows:

a. Carefully remove the four phillips head screws (E) securing the 

head/knee P.C. board (F) to the inner housing (G).

b. Slide the control cable connector (K) from its terminal on the 

head/knee P.C. board.

c. Side the cable connector (J) from its terminal on the head/knee P.C. 

board, and remove the head/knee P.C. board.

d. Connect the cable (J) leading from the hilow P.C. board (C) to its 

terminal on the replacement head/knee P.C. board (F).

e. Connect the control cable connector (K) to its terminal on the 

head/knee P.C. board (F).

Содержание P870








































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды