manualshive.com logo in svg

Hill-Rom P870, Руководство пользователя

Поделиться
Скачать
Hill-Rom P870 Скачать руководство пользователя страница 103

Electrical Theory of Operation

Chapter 3: Theory of Operation

Page 3 - 6

Resident

TM

 LTC Bed Service Manual (man136rc)

3

Electrical Theory of Operation

The Hill-Rom

®

 Resident

TM

 LTC bed incorporates three separate motor actuators 

to provide the following operational features:

• Hilow (bed height)–this function raises and lowers the entire sleep surface.

• Head section–this function raises and lowers the head section of the bed.

• Knee section–this function raises and lowers the knee section of the bed.

• Automatic contour–this is an automatic function that is activated during 

operation of the head section (unless locked out). As the head section 
inclines, the knee section of the bed also inclines to a maximum of 15

o

 

(± 2

o

). If the automatic contour is temporarily disabled by pressing both the 

HEAD Up and KNEE Down buttons at the same time, releasing the KNEE 
Down button will allow the automatic contour function to activate 
regardless of the degree of head section inclination.

These features are controlled by using the handset and/or the optional siderail 
control panels in conjunction with the control lockout box.

When the Resident

TM

 LTC bed is plugged into a 120V AC, 60 Hz power source, 

a transformer within the control box reduces the incoming voltage to 42V AC. 
This 42V AC is then rectified to 42V DC and supplied to the input side of a 
“normally open” switching circuit and to the input side of a “normally open” 
motor actuator circuit.

The switching circuit consists of the following:

• The coils of six different relays, one for each possible motor actuator 

function

• Four isolation switches in the caregiver control lockout box

• Six momentary contact switches in the handset control

• Six momentary contact switches in each siderail control

• Two limit switches in the automatic contour module

Содержание P870








































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды