53
52
EN
EN
ES Declaration of Conformity
Subject of declaration - model, product identification:
Heron® 8895105
Petrol-powered sludge pump
1300 l/min; 26 m,
∅
3“
Manufacturer Madal Bal a.s. • Bartošova 40/3, CZ-760 01 Zlín • Company ID No.: 49433717
hereby declares
that the product described above is in conformity
with all relevant stipulations of harmonisation legal regulations of the European Union:
2006/42 ES; (EU) 2011/65; (EU) 2014/30;
(EU) 2016/1628, 2000/14 ES.
This declaration is issued under the exclusive responsibility of the manufacturer.
Harmonisation norms (including their amendments, if any exist),
which were used in the assessment of conformity and on the basis
of which the Declaration of conformity is issued:
EN ISO 12100:2010; EN 60204-1:2018; EN 809:1998+A1:2009; EN 61000-6-1:2007 until 22.02.2022,
thereafter according to EN IEC 61000-6-1:2019; EN 61000-6-3:2007; EN ISO 3744:2010, ISO 6395:2008,
EN ISO 4871:2009; EN IEC 63000:2018.
Measured acoustic power level of the equipment representing the given model, uncertainty K: 90.2 dB(A); K = ±3 dB(A)
Guaranteed acoustic power level of the equipment: 93 dB(A)
The technical documentation 2006/42 ES, 2000/14 ES was drawn up by Martin Šenkýř at the address of Madal Bal , a.s.,
Průmyslová zóna Příluky 244, 760 01 Zlín, Czech Republic. The Technical Documentation (2006/42 ES, 2000/14 ES) is
available at the above address of Madal Bal, a.s. Conformity assessment procedure (2006/42 ES, 2000/14 ES) Verification
of the individual products by the notified entity no.: 1282
Ente Certificatione Macchine Srl, Via Ca´ Bella, 243- Loc. Castello di Serravalle-40053 Valsamoggia (BO) Italy.
Approval of exhaust gas emissions (EU) 2016/1628, see label on the machine.
Place and date of issue of ES Declaration of Conformity
: 14/06/2021
On behalf of Madal Bal, a.s.
Martin Šenkýř
Member of the Company‘s Board of Directors
Storage
WARNING!
When transporting the engine, ensure that the engine
switch (2) is in the OFF position (OFF, 0) and that the fuel
tank is properly closed so that fuel spillage is prevented.
Ensure that fuel is not spilled during transport. If it never-
theless occurs, ensure that the area is completely dry and
that petrol fumes are thoroughly ventilated.
BEFORE STORING THE MACHINE FOR AN
EXTENDED PERIOD OF TIME:
• Clean the external parts of the engine.
• Drain the petrol:
1. Close the fuel tap (10) and remove and empty out
the setting cup (12).
2. Open the fuel tap (10).
3. Drain the petrol from the fuel tank
into an appropriate container.
4. Screw the setting cup back in.
5. Drain the petrol from the carburettor by loosening
and removing the drain bolt (11).
• Prior to storing for an extended period of time, remove
the oil.
• Screw out the spark plug and allow approx. 1 teaspoon
of oil to flow into the cylinder. Then pull on the starting
cord 2-3x. This will create an even protective oil film in
the area of the cylinder (fuel tank).
• Rotate the engine by pulling on the handle of the
starter cord and stop the piston in the top end position.
In this way, the exhaust and suction valve will remain
closed.
• Screw the spark plug back in.
• Place the pump into a safe, dry room.
Diagnostics
and troubleshooting
potential faults
The engine does not start-up
• Is the engine switch in the ON position?
• Is the fuel tap open?
• Is there sufficient fuel in the tank?
• Is there a sufficient amount of oil in the engine?
• Is the spark plug cable connected?
• Is the spark plug generating a spark?
Spark plug function test
ATTENTION:
First ensure that there is no spilled petrol or other fla-
mmable substances in the vicinity. When testing, use
suitable protective gloves. When working without gloves
there is a risk of injury by electrical shock! Before remo-
ving it, make sure that the spark plug is not hot!
1. Remove the spark plug.
2. Seat the spark plug into the connector (cap).
3. Hold the spark plug on the frame of the engine (e.g.
cylinder head) and pull on the starting cord.
4. If there is no sparking, replace the spark plug. If the
sparking is in order, reinstall the spark plug and conti-
nue starting the engine according to the manual.
5. If the engine does not start even after this, have the
repairs performed at a professional service centre.
If you are unable to remedy the malfunction, have the
repairs performed at a professional service centre.
