Henny Penny Evolution Elite EEE-153 Скачать руководство пользователя страница 22

Страница: 22 / 80

During normal operation, the control automatically monitors

the oil level in the vat. If the control senses the oil level too

low, the unit automatically pumps oil from the BIB into the vat

to keep the oil at the proper level.

Manual Top-Off

If the oil level is a little low, oil can be added to the vat at any

time from the BIB to raise the oil level to the proper level by

following the steps below. This procedure is NOT to be used

to fill an empty vat

1. Press and hold (either one-full vat) until display

shows “*FILTER MENU*”, along with “1.EXPRESS

FILTER”.

2. Press

5 times until “6.FILL FROM BIB” shows in

the display.

3. Press

button, “FILL VAT” “

=PUMP” “

=DONE” is

displayed.

4. Press and hold

button and display shows “FILLING”

and the oil is pumped from the BIB to the vat.

5. Once vat is full, release

button, “FILL VAT”

“

=PUMP” “

=DONE” displays. Press

button twice

for normal operation

When selecting a product, if “XXX XXX” shows in the dis-

play, the setpoint temperature is not correct for this product.

To change the setpoint temperature for the desired product:

Press product button, for ex: (FRY).

Display shows “XXX XXX”.

Press and hold a timer button or for 5

seconds and then “FRY” shows in display.

Allow oil temperature to reach setpoint temperature

before dropping product.

1. Control displays “BIB IS LOW” and an alarm sounds.

2. Open right door and pull BIB from unit. Pull the cap from

top of BIB and discard empty BIB and replace with full

one. Figure 1

3-8. SELECTING A PRODUCT

WITH A DIFFERENT

SETPOINT

3-9

REPLACING THE BIB

Figure 1

3-7. OIL GUARDIAN™

(Auto Top-Off)

Aug. 2011

Содержание Evolution Elite EEE-153

















































































Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Похожие инструкции для Evolution Elite EEE-153

Бренды по названию

Популярные бренды

Henny Penny Evolution Elite EEE-153, Руководство оператора

Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Похожие инструкции для Evolution Elite EEE-153

Бренды по названию

Популярные бренды