Henny Penny Evolution Elite EEE-153 Скачать руководство пользователя страница 73

Страница: 73 / 80

6-3. CLOCK SET

1. Press and hold the button for 5 seconds until “LEVEL

2”, followed by, “SP PROG” and “ENTER CODE” show in

the display.

2. Press the button again and “CLK SET” and “ENTER

CODE” flash in the left display.

3. Enter code 1, 2, 3 (first 3 product buttons).

4. “CS-1 ENTER DATE MM-DD-YY” flashes in the left

display. Use the product buttons to set the date in the right

display.

5. Press button and “CS-2 ENTER TIME” flashes in the

left display and the time flashes in the right display. Press

the or , or use product buttons, to change the time.

6. Press button and “CS-2 ENTER TIME” flashes in the

left display and “AM” or “PM” flashes in the right display.

Use the or buttons to choose AM or PM.

7. Press button and “CS-3 TIME FORMAT” flashes in

the left display and “12-HR” or “24-HR” shows in the right

display. Use the or buttons to choose a 12 hour

time format or a 24 hour time format.

8. Press button and “CS-4 DAYLIGHT SAVING TIME”

flashes in the left display. Use the or buttons to

choose daylight saving time for your area: 1.OFF; 2.US

(2007 & after); 3.EURO; or 4.FSA (US before 2007).

The Data Logging, Heat Control, Tech, Stat and Filter Control

Modes are advanced diagnostic and program modes, mainly for

Henny Penny use only. For more information on these modes,

contact the Service Department at 1-800-417- 8405 or 1-937-

456-8405.

6-4. DATA LOGGING, HEAT

CONTROL, TECH, STAT,

AND FILTER CONTROL

MODES

Aug. 2011

Содержание Evolution Elite EEE-153

















































































Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Бренды по названию

Популярные бренды

Henny Penny Evolution Elite EEE-153, Руководство оператора

Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Бренды по названию

Популярные бренды