Henny Penny Evolution Elite EEE-153 Скачать руководство пользователя страница 70

Страница: 70 / 80

6-1. SPECIAL PROGRAM

MODE (Continued)

Autolift Enabled (SP-21)

Press

button and “SP-21 AUTOLIFT ENABLED?”

flashes in the left display. Press the or buttons

to choose “YES LIFT” or “NO LIFT”.

If fryer is fitted with the auto-lift option, SP-21 must be set

to “YES LIFT”, otherwise, set SP-21 to “NO LIFT”.

Bulk Oil Supply (SP-22)

Press

button and “SP-22 BULK OIL SUPPLY?”

flashes in the left display. Press the or buttons

to choose “YES SUPL” or “NO SUPL”.

Set to YES if the oil is pumped into the vats from an

outside oil reservoir. Otherwise, set SP-22 to NO.

Bulk Oil Disposal (SP-23)

Press

button and “SP-23 BULK OIL DISPOSE?”

flashes in the left display. Press the or buttons

to choose “YES DISP” or “NO DISP”.

Set to “YES DISP” if the oil is pumped from the vats to an

outside oil reservoir when disarding the oil. Otherwise, set

SP-23 to “NO DISP”.

Serial Number Log (SP-24)

Press

button and “SP-24 S/N

EDIT” flashes in the

displays, along with the serial number of the unit. THIS

SERIAL NUMBER SHOULD MATCH THE SERIAL

NUMBER ON THE DATA PLATE, ON THE DOORS. IF

NOT, IT CAN BE RECORDED.

Program Code Change (SP-25)

This allows the operator to change the program code (factory

set at 1, 2, 3) used to access Product Programming and Level 2

Program Mode.

Press

button and “SP-25 CHANGE MGR CODE?

1=YES” flash in the display. Press

and “ENTER

NEW CODE, P=DONE, I=QUIT show scrolls through the

display. Press the product buttons for new code.

If satisfied with code, press and “REPEAT NEW

CODE, P=DONE, I=QUIT, shows in display. Press same

code buttons.

Aug. 2011

Содержание Evolution Elite EEE-153

















































































Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Бренды по названию

Популярные бренды

Henny Penny Evolution Elite EEE-153, Руководство оператора

Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Бренды по названию

Популярные бренды