Henny Penny Evolution Elite EEE-153 Скачать руководство пользователя страница 31

Страница: 31 / 80

3-11.

B SMART TOUCH DAILY

FILTERING

Put on protective gear: Be sure to use all approved safety equipment

in-cluding, apron, face shield and gloves. Never begin filtering until

you’re wearing all safety gear. Hot oil can cause severe burns.
Moving the fryer or filter drain pan while containing hot oil is not

recommended. Hot oil can splash out and severe burns could result.

Check Filter Pan: Use a new filter pad on the first filter of each day,

but the same filter pad can be used the rest of the day, except for fish

vats. Change the filter pad after filtering a fish vat.

Make sure that the filter pipe is tightly connected, and that the filter

drain pan

is as far back under fryer as it will go and the filter pan

cover is in place. If the

filter drain pan or cover is not in place, the

display shows “CHK PAN”

Make sure oil is hot: The best results are obtained when the frying oil

is filtered at the normal frying temperature.

Press and hold

until display shows “1.AUTO FILTER?”.

Press and release ▼ button and display shows 2.MAINT FILTER?

Press

button for YES and display shows “MAN FILTER” YES NO.

Press

√

button for YES and display shows “DRAINING” and the oil

drains from the vat, or press X button for NO and controls return

to normal operation. (If control suspects oil in drain pan “CAUTION

IS THERE OIL IN PAN? YES NO” shows in display. Make sure

drain pan is empty before proceeding

)

Once oil has drained from vat, remove the basket support from the

vat. Figure 2

Use protective cloth or gloves when lifting the basket support. The

sup-port may be hot and burns could result.

Use the Hi-Temp Pad Holder, pad, and a small amount of KAY QSR

Fryer Cleaner to scrub the walls, corners and bottom of the inside of

the vat. Use the Hi-Temp Detail Brush to clean in between and un-

derneath burner tubes, corners of vats and other hard-to-reach areas.

Be careful not to damage sensing probes.

Oct

. 201

FIRE RISK

Do not exert pressure on the heating elements or fire may occur,

resulting in personal injury and/or property damage.

Содержание Evolution Elite EEE-153

















































































Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Бренды по названию

Популярные бренды

Henny Penny Evolution Elite EEE-153, Руководство оператора

Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Бренды по названию

Популярные бренды