Henny Penny Evolution Elite EEE-153 Скачать руководство пользователя страница 77

Страница: 77 / 80

7-2. ERROR CODES

In the event of a control system failure, the digital display

shows an error message. The message codes are shown in the

DISPLAY column below. A constant tone is heard when an er-

ror code is displayed, and to silence this tone, press any button.

Aug. 2011

DISPLAY

CAUSE

CORRECTION

“E-4”

Control board overheating

Turn switch to OFF position, then turn switch back

to ON; if display shows “E-4”, the control board is

getting too hot; check the louvers on each side of the

unit for obstructions

“E-5”

Oil overheating

Turn switch to OFF position, then turn switch back to

ON; if display shows “E-5”, the heating circuits and

temperature probe should be checked

“E-6A”

Temperature probe open

Turn switch to OFF position, then turn switch back to

ON; if display shows “E-6A”, the temperature probe

should be checked

“E-6B”

Temperature probe shorted

Turn switch to OFF position, then turn switch back to

ON; if display shows “E-6B”, the temperature probe

should be checked

“E-10”

High limit

Let unit cool down (15-20 minutes), using the high limit

tool on the inside of the LH door and gently pushing it

into the hole in the heating element hinge; if high limit

does not reset, high limit must be replaced

“E-15”

Drain switch

Make sure drain knob is completely pushed-in; if E-15

persists, have drain switch checked

“E-18-A”

“E-18-B”

“E-18-C”

Left level sensor open

Right level sensor open

Both level sensors open

Turn switch to OFF position, then turn switch back to

ON; if display still indicates a failed sensor, have the

connections checked the control board; have sensor

checked & replaced if necessory

Содержание Evolution Elite EEE-153

















































































Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Бренды по названию

Популярные бренды

Henny Penny Evolution Elite EEE-153, Руководство оператора

Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Бренды по названию

Популярные бренды