Henny Penny Evolution Elite EEE-153 Скачать руководство пользователя страница 50

Страница: 50 / 80

3-19. INFO BUTTON STATS

Actual Oil Temperature

1. Press and the actual oil temperature shows in the

display, for each vat.

Set-point Temperature

2. Press twice and SP shows in the display, along with

the set-point (preset) temperature of each vat.

Recovery Information for each Vat

3. Press 3 times and REC shows in the left display and

the recovery time that oil temperature went from 250°F

(121°C) to 300°F (149°C) shows in the right display.

For example, “REC 5:30” means it took 5 minutes and 30

seconds for the oil temperature to recover to 300°F (149°C)

from 250°F (121°C).

If no buttons are pressed within 5 seconds in any of stats

modes, the controls revert back to normal operation.

Cook Cycles Remaining before Filtering

1. Press and release either button and the left display

shows “COOKS REMAINING” and the right display

shows the number of cook cycles before the next auto filter.

For example, “REMAINING” “3” “6” means after 3 more

cook cycles on the left vat, the controls asks the operator if

they are ready to filter or not. But, 6 more cook cycles

remain on the right vat.

Time and Date

2. Press either twice and ‘FILTERED” shows in the

diplays, along with the time-of-day and date of the last

filter.

3-20. FILTER BUTTON STATS

Aug. 2011

Содержание Evolution Elite EEE-153

















































































Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Бренды по названию

Популярные бренды

Henny Penny Evolution Elite EEE-153, Руководство оператора

Результаты поиска

Содержание Evolution Elite EEE-153

Отзывы:

Бренды по названию

Популярные бренды