manualshive.com logo in svg

Helmer ACX001, Руководство по техническому обслуживанию

Поделиться
Скачать
Helmer ACX001 Скачать руководство пользователя страница 41

360179-A/B

40

Troubleshooting

Section IV:  Troubleshooting

11 Troubleshooting

WARNING

Rear door must remain shut and locked while unit is in operation to protect the integrity of 

stored product.

CAUTION

Review all safety instructions prior to troubleshooting.  Refer to 

Section I

, 

Item

 

2

.

NOTE 

For service information or to order replacement parts, contact Haemonetics

 Corporation 

BloodTrack

 Customer Support at 877.996.7877. 

11 .1 

Compartment Access Circuit Boards and Sensors Diagnostic References

11 .1 .1 

IRACS Horizontal Circuit Board LED Indicators

NOTICE

The IRACS horizontal circuit board is sensitive to static electricity and can be damaged 

by electrostatic discharge.  Use proper ESD precautions when handling the board.

NOTE 

If the IRACS horizontal circuit board must be replaced, contact Haemonetics

®

 

Corporation BloodTrack

®

 Customer Support for replacement parts. Part number 800262-1.

The IRACS horizontal circuit board includes several labeled LEDs which indicate the status of the circuit 
board, the status of the multiple voltages used on the circuit board, and the status of the diagnostic 
functions available on the circuit board.

11 .1 .2 

Check Circuit Board Status

The “heart beat” (HRTBT) LED indicates the operational status of the circuit board.

HRTBT LED illuminated

► 

Single flash of “HRTBT” LED indicates board is functioning normally.

► 

Double flash of “HRTBT” LED indicates board is not functioning normally, because the board 

recognizes its row address as being outside of a valid, pre-determined range of addresses.

Содержание ACX001










































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды