manualshive.com logo in svg

Helmer ACX001, Руководство по техническому обслуживанию

Поделиться
Скачать
Helmer ACX001 Скачать руководство пользователя страница 26

360179-A/B

25

Maintenance & Service

Alarm Settings

Restored Value

Upper Probe Low Temperature (Setpoint)

2.0 ºC

Upper Probe Low Temperature (Time Delay)

0 minutes

Air Probe High Temperature (Setpoint)

14.0 ºC

Air Probe High Temperature (Time Delay)

3 minutes

Air Probe Low Temperature (Setpoint)

-6.0 ºC

Air Probe Low Temperature (Time Delay)

3 minutes

Compressor Temperature (Setpoint)

50.0 ºC

Compressor Temperature (Time Delay)

5 minutes

Power Failure

1 minute

Probe Failure

0 minutes

Door Open (Time)

10 minutes

8 .6 

Restore Factory Default Settings

NOTICE

► 

If Factory Default Settings are restored, all calibration values and User PINs will be 

lost. 

► 

Contact Haemonetics

 

Corporation BloodTrack

 Customer Support prior to restoring 

Factory Default Settings.

Restore settings:

1 

Touch 

Home

, 

i.C³ APPS

, 

Settings

.

2 

Enter the Settings password.

3 

Touch 

Restore Factory Settings

.

► 

The 

“Are you sure you want to restore factory settings?”

 message is displayed

► 

Touch 

√

.  The message screen closes and factory settings are restored

► 

Touch 

X

.  The message screen closes and factory settings are not restored

4 

Touch 

Home

.

8.7 

View System Information

1 

Touch 

Home

, 

i.C³ APPS

, 

Contacts

.

► 

The Contacts screen is displayed

2 

Touch 

More Info

.

► 

The Versions screen is displayed, including software configuration, software revision numbers, 

hardware serial numbers, i.C³ IP address, and i.C³ MAC address

3 

Touch 

Home

.

Содержание ACX001










































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды