manualshive.com logo in svg

Helmer ACX001, Руководство по техническому обслуживанию

Поделиться
Скачать
Helmer ACX001 Скачать руководство пользователя страница 24

360179-A/B

23

Installation & Configuration

8 .3 .1 .1 

Temperature Setpoint

NOTE

► 

Default chamber temperature setpoint is 4.0 ºC.

► 

Setpoint can be changed from the i.C

3 

and from the Haemonetics

®

 BloodTrack

®

 

interface.

The temperature setpoint is the desired temperature of the HaemoBank™ for stored product.

Change the temperature setpoint if:

► 

Your organization requires a chamber temperature other than 4.0 ºC

Perform the following:

1 

Touch 

Home

, 

i.C³ APPS

, 

Settings

.

2 

Enter the Settings password.

3 

Touch 

+

 or 

–

 on the 

Temperature Setpoint

 spin box to select desired setting.

4 

Touch 

Home

.

8 .4 

Sensor Calibration

Sensor calibration values are programmed at the factory.  Calibration values can be viewed through the 
i.C³ Sensor Calibration screen.

 

Sensor Calibration screens

8.4.1 

View Sensor Calibration Values

1 

Touch 

Home

, 

i.C³ APPS

, 

Settings

.

2 

Enter the Settings password.

3 

Touch 

Sensor Calibration

.

► 

Sensor offset values and their current temperature readings are displayed

4 

Touch 

Home

.

Setting

Initial Factory Value

Simulated product 

probe

Varies (set at the factory to match 

a NIST traceable independent 

thermometer)

Control probe
Air probe
Compressor probe

Содержание ACX001










































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды