manualshive.com logo in svg

Hartzell HC-82VF-1, Руководство пользователя

Поделиться
Скачать
Hartzell HC-82VF-1 Скачать руководство пользователя страница 8

Propeller Owner's Manual

175

Page  6 

Dec/05

61-00-75

REVISION HIGHLIGHTS  

REVISIONS HIGHLIGHTS

1.  Introduction

A.  General

This is a list of current revisions that have been issued 
against this manual. Please compare it to the RECORD OF 
REVISIONS page to ensure that all revisions have been 
added to the manual.  

B.  Components

(1)  Revision No. indicates the revisions incorporated in this 

manual.

(2)  Issue Date is the date of the revision.

(3)  Comments indicates the level of the revision.

(a)  New Issue is a new manual distribution. The manual 

is distributed in its entirety. All the page revision 
dates are the same and no change bars are used.

(b)  Reissue is a revision to an existing manual that 

includes major content and/or major format 
changes. The manual is distributed in its entirety. 
All the page revision dates are the same and no 
change bars are used.

(c)  Major Revision is a revision to an existing manual 

that includes major content or minor content 
changes over a large portion of the manual. The 
manual is distributed in its entirety. All the page 
revision dates are the same, but change bars are 
used to indicate the changes incorporated in the 
latest revision of the manual.

(d)   Minor Revision is a revision to an existing manual 

that includes minor content changes to the 
manual. Only the revised pages of the manual are 
distributed. Each page retains the date and the 
change bars associated with the last revision to that 
page. 

OBSOLETE PROPELLER MODELS. SEE COVER PAGE  

WARNINGS AND SERVICE BULLETIN HC-SB-61-331

 

 

Содержание HC-82VF-1



























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды