Hartzell HC-82VF-1 Скачать руководство пользователя

Страница: 169 / 250

INSTALLATION AND REMOVAL

61-00-75

Propeller Owner’s Manual

175

Page 3-89

Rev. 1 Jun/11

F. Removing F Flange Propeller Models HC-83(X,V)F-3( )( )

Refer to Figure 3-11.

NOTE

: If the propeller is equipped with a de-ice system,

follow the manufacturer’s instructions for removing

whichever components are necessary for propeller

removal.

(1) Remove the spinner dome if applicable

(a) Remove the screws and washers that secure the

spinner dome to the bulkhead.

(b) Remove the spinner dome.
(c) Remove layers of masking or duct tape from each

blade shank, if applicable.

CAUTION

THE BETA TUBE MUST BE REMOVED

BEFORE THE PROPELLER ASSEMBLY IS

REMOVED FROM THE AIRCRAFT. REFER
TO THE AIRCRAFT MAINTENANCE
INSTRUCTION MANUAL.

(2) Remove the beta tube.

WARNING 1

: DURING ENGINE INSTALLATION OR

REMOVAL, USING THE PROPELLER TO
SUPPORT THE WEIGHT OF THE ENGINE
IS NOT AUTHORIZED. UNAPPROVED
INSTALLATION AND REMOVAL

TECHNIQUES MAY CAUSE DAMAGE TO

THE PROPELLER THAT MAY LEAD TO

FAILURE AND RESULT IN AN AIRCRAFT
ACCIDENT.

WARNING 2

: DURING PROPELLER REMOVAL,

AIRFRAME MANUFACTURER’S
MANUALS AND PROCEDURES MUST

BE FOLLOWED BECAUSE THEY MAY

CONTAIN ISSUES VITAL TO AIRCRAFT

SAFETY THAT ARE NOT CONTAINED

IN THIS MANUAL OR IN THE HARTZELL
PROPELLER OVERHAUL MANUALS.

OBSOLETE PROPELLER MODELS. SEE COVER PAGE

WARNINGS AND SERVICE BULLETIN HC-SB-61-331

Содержание HC-82VF-1



























































































































































































































































Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды

Hartzell HC-82VF-1, Руководство пользователя

Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды