Hartzell HC-82VF-1 Скачать руководство пользователя страница 146

Страница: 146 / 250

INSTALLATION AND REMOVAL

61-00-75

Propeller Owner’s Manual

175

Page 3-66

Rev. 1 Jun/11

(b) Remove the safety wire (if installed) from the link pin

units.

(c)  Remove the safety screw from each link pin unit.
(d)  Remove each link pin unit.
(e)  The piston ears and guide collar should have

corresponding index numbers (1 and 2 on a 2-

blade propeller; 1, 2, and 3 on a 3-blade propeller)

impression-stamped or marked with a felt-tipped

pen. If they are not marked, number them with a felt-

tipped pen.

NOTE

: This will make sure that the components

are reassembled in their original location.

(f) Slide the link arms out of the piston slots.
(g) Remove the socket head cap screw (Table 3-1), jam

nut, and washer from each piston guide rod.

(h) Slide the piston off the cylinder.

CAUTION

THE SPRING ASSEMBLY MUST BE

REMOVED BEFORE INSTALLING THE
PROPELLER ON THE AIRCRAFT. IF THE

SPRING ASSEMBLY HAS ALREADY BEEN

REMOVED, PROCEED TO STEP 4.J.(3).

(2) Spring assembly removal:

Refer to Figure 3-18.
(a) Remove the safety wire (if installed) from the feather

stop screws.

(b) Remove the two screws from each of the two feather

stops on the front spring retainer.

OBSOLETE PROPELLER MODELS. SEE COVER PAGE

WARNINGS AND SERVICE BULLETIN HC-SB-61-331

Содержание HC-82VF-1



























































































































































































































































Результаты поиска

Содержание HC-82VF-1

Отзывы:

Бренды по названию

Популярные бренды

Hartzell HC-82VF-1, Руководство пользователя

Результаты поиска

Содержание HC-82VF-1

Отзывы:

Бренды по названию

Популярные бренды