Hartzell HC-82VF-1 Скачать руководство пользователя страница 105

Страница: 105 / 250

INSTALLATION AND REMOVAL

61-00-75

Propeller Owner’s Manual

175

Page 3-25

Dec/05

CAUTION

MAKE SURE THAT COMPLETE

AND TRUE SURFACE CONTACT
IS ESTABLISHED BETWEEN THE
PROPELLER HUB FLANGE AND THE
ENGINE FLANGE.

(7) Slide the propeller flange onto the engine flange,

against the starter ring gear and shim.

NOTE

: Insert the engine bushings into the

counterbores that encircle the propeller

mounting bolts in the propeller flange.

CAUTION

NEW PROPELLER MOUNTING BOLTS

MUST BE USED WHEN INITIALLY

INSTALLING A NEW OR OVERHAULED
PROPELLER.

(8) Thread the four pre installed mounting bolts (Table 3-1)

through the propeller flange from the propeller side, and

into the bushings in the engine flange. Refer to Figure

3-6.

NOTE

: The mounting bolts are preinstalled during

the assembly of the propeller. Replacement of

one of these bolts between overhauls must be

performed only by qualified personnel at an

appropriately licensed propeller repair facility

(9) Install the remaining two mounting bolts.
(10) Use a torque wrench with the appropriate torque

wrench adapter (Figure 3-6) to torque all mounting

bolts in sequence. Refer to Table 3-2 and Figure 3-4 to

determine the proper torque value to which the torque

wrench must be set.

NOTE

: Refer to the Tools, Consumables, and

Expendables section in this chapter for a list

of applicable torque wrench adapters.

(a) Torque the mounting bolts to half of the final

torque in staggered sequence, beginning with any

mounting bolt.

(b) Final torque the bolts in sequence, beginning with

any mounting bolt, and moving around the clock in

either direction.

OBSOLETE PROPELLER MODELS. SEE COVER PAGE

WARNINGS AND SERVICE BULLETIN HC-SB-61-331

Содержание HC-82VF-1



























































































































































































































































Результаты поиска

Содержание HC-82VF-1

Отзывы:

Бренды по названию

Популярные бренды

Hartzell HC-82VF-1, Руководство пользователя

Результаты поиска

Содержание HC-82VF-1

Отзывы:

Бренды по названию

Популярные бренды