Hartzell HC-82VF-1 Скачать руководство пользователя страница 160

Страница: 160 / 250

INSTALLATION AND REMOVAL

61-00-75

Propeller Owner’s Manual

175

Page 3-80

Rev. 1 Jun/11

WARNING 3

: USE CAUTION DURING PROPELLER

REMOVAL WHEN THE START LOCKS
ARE ENGAGED. IF THE BLADES ARE

RELEASED SUDDENLY, THE EXTREME

FORCE CAN CAUSE SERIOUS INJURY

AND DAMAGE TO THE PROPELLER.

(2) Routine propeller engine shutdown will engage the start

lock units, preventing the propeller from feathering. To

permit access to the of the spinner mounting bolts, the

start locks should remain engaged during the removal of

the propeller.

(3) Remove the safety wire on the propeller mounting bolts.

WARNING

MAKE SURE THE SLING IS RATED UP TO

800 POUNDS (363 KG.) TO SUPPORT THE

WEIGHT OF THE PROPELLER ASSEMBLY

DURING REMOVAL.

(4) Support the propeller assembly with a sling.

NOTE 1

: To permit rotation of the propeller for ease of

bolt removal, supporting the propeller with a

sling may be delayed until all but two mounting

bolts and washers have been removed.

NOTE 2

: If the propeller will be reinstalled, and it

has been dynamically balanced, make

an identifying mark (with a felt-tipped pen

only) on the propeller hub and a matching

mark on the engine flange to make sure of

proper positioning of the propeller during

reinstallation. This will prevent dynamic

imbalance.

OBSOLETE PROPELLER MODELS. SEE COVER PAGE

WARNINGS AND SERVICE BULLETIN HC-SB-61-331

Содержание HC-82VF-1



























































































































































































































































Результаты поиска

Содержание HC-82VF-1

Отзывы:

Бренды по названию

Популярные бренды

Hartzell HC-82VF-1, Руководство пользователя

Результаты поиска

Содержание HC-82VF-1

Отзывы:

Бренды по названию

Популярные бренды