Hartzell HC-82VF-1 Скачать руководство пользователя страница 165

Страница: 165 / 250

INSTALLATION AND REMOVAL

61-00-75

Propeller Owner’s Manual

175

Page 3-85

Rev. 1 Jun/11

(9) Remove four propeller mounting bolts and washers.

NOTE 1

: Two of the propeller mounting bolts and

washers cannot be removed from the propeller

hub due to interference with other propeller

parts.

NOTE 2

: For propeller removals between overhaul

intervals, mounting bolts and washers may be

reused if they are not damaged or corroded.

CAUTION

USE ADEQUATE PRECAUTIONS TO

PROTECT THE PROPELLER ASSEMBLY

FROM DAMAGE WHEN IT IS REMOVED
FROM THE AIRCRAFT ENGINE AND
WHEN IT IS STORED.

(10) Remove and discard the shaft O-ring.
(11) Remove the shim.
(12) Using the support sling, lift the propeller from the

mounting flange.

(13) If the spinner was manufactured by Hartzell Propeller:

(a)  Do not remove the spinner adapter ring.
(b)  Visually inspect the spinner adapter ring for cracks.
(c)  If cracks are found in the spinner adapter ring,

remove it from the engine starter ring gear and

replace it.

OBSOLETE PROPELLER MODELS. SEE COVER PAGE

WARNINGS AND SERVICE BULLETIN HC-SB-61-331

Содержание HC-82VF-1



























































































































































































































































Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды

Hartzell HC-82VF-1, Руководство пользователя

Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды