Hartzell HC-82VF-1 Скачать руководство пользователя

Страница: 33 / 250

Propeller Owner’s Manual

175

INTRODUCTION

61-00-75

Page 1-3

Rev. 1 Jun/11

1. Purpose

CAUTION:

KEEP THIS MANUAL WITH THE PROPELLER,

OR WITH THE AIRCRAFT ON WHICH IT IS

INSTALLED, AT ALL TIMES. THE LOG BOOK
RECORD WITHIN THIS MANUAL MUST BE
MAINTAINED, RETAINED CONCURRENTLY,

AND BECOME A PART OF THE AIRCRAFT

AND ENGINE SERVICE RECORDS.

A. This manual supports the following two and three-bladed,

“8” type steel hub reciprocating propellers: constant speed,

nonfeathering; constant speed, feathering; constant speed,

reversing; and constant speed, feathering, and reversing.

NOTE

: All propeller models included in this manual use

aluminum propeller blades.

B. The purpose of this manual is to enable qualified personnel

to install, operate, and maintain a Hartzell propeller.

Separate manuals are available concerning overhaul

procedures and specifications for the propeller.

This manual in

cludes

several design types.

(1)

Sample hub and blade model numbers within this design

are

included

in the Description and Operation chapter of

this manual.

(2) Parentheses shown in the propeller model designations

in this or other Hartzell publications indicate letter(s)

and/or number(s) that may or may not be present

because of different configurations permitted on the

various aircraft installations.

(3) Definitions of propeller model designations and further

details of letters that may be present are shown in the

Description and Operation chapter of this manual.

2. Airworthiness Limitations

Refer to the

Airworthiness Limitations section

of this manual

for Airworthiness Limits information.

OBSOLETE PROPELLER MODELS. SEE COVER PAGE

WARNINGS AND SERVICE BULLETIN HC-SB-61-331

Содержание HC-82VF-1



























































































































































































































































Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды

Hartzell HC-82VF-1, Руководство пользователя

Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды