Hartzell HC-82VF-1 Скачать руководство пользователя страница 157

Страница: 157 / 250

INSTALLATION AND REMOVAL

61-00-75

Propeller Owner’s Manual

175

Page 3-77

Rev. 1 Jun/11

WARNING

MAKE SURE THE SLING IS RATED UP TO

800 POUNDS (363 KG.) TO SUPPORT THE

WEIGHT OF THE PROPELLER ASSEMBLY

DURING REMOVAL.

(3) Support the propeller assembly with a sling.

NOTE 1

: To permit rotation of the propeller for ease of

bolt removal, supporting the propeller with a

sling may be delayed until all but two mounting

bolts and washers have been removed.

NOTE 2

: If the propeller will be reinstalled, and it

has been dynamically balanced, make

an identifying mark (with a felt-tipped pen

only) on the propeller hub and a matching

mark on the engine flange to make sure of

proper positioning of the propeller during

reinstallation. This will prevent dynamic

imbalance.

CAUTION

DISCARD THE PROPELLER MOUNTING

BOLTS AND WASHERS IF THEY ARE

DAMAGED OR CORRODED, OR IF
THE PROPELLER IS REMOVED FOR
OVERHAUL.

(4) Remove the propeller mounting bolts from the engine

flange.

(5) Remove two propeller mounting bolts and washers.

NOTE 1

: Four of the propeller mounting bolts and

washers cannot be removed from the propeller

hub due to interference with other propeller

parts.

NOTE 2

: For propeller removals between overhaul

intervals, mounting bolts and washers may be

reused if they are not damaged or corroded.

OBSOLETE PROPELLER MODELS. SEE COVER PAGE

WARNINGS AND SERVICE BULLETIN HC-SB-61-331

Содержание HC-82VF-1



























































































































































































































































Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды

Hartzell HC-82VF-1, Руководство пользователя

Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды