manualshive.com logo in svg

Harman Martin Exterior Projection 1000, Руководство пользователя, Страница: 40 / 60

Поделиться
Скачать
Harman Martin Exterior Projection 1000 Скачать руководство пользователя страница 40

 

40 

Exterior Projection 1000 User Manual 

5.  See illustration below. Wearing clean gloves, hold the gobo with the dark side facing up. Match 

up the alignment marks (arrowed) in the gobo and goboholder. Lay the new gobo flat in the 
goboholder.   

 

 

 
 

Gobos 5 and 6 only 

Gobos 5 and 6 are textured glass and require a thrust washer. See illustration below. Place the 
black thrust washer (arrowed) over the gobo before you go on to the next step.   

 

 

 

1.  See illustration below. Note the end of the gobo retaining spring with the bend (arrowed) that is 

used for levering the spring out of the goboholder. Making sure that the bend in the spring is at 
the top (as shown below), closest to you, press the spring down into the goboholder until the 
spring clips into its recess in the goboholder. Check that the spring is secure and that the gobo 
is still sitting flat in the goboholder.   

 

 

 

Содержание Martin Exterior Projection 1000





























































Отзывы:

Нет отзывов