Harman Martin Exterior Projection 1000 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 60

Harman Martin Exterior Projection 1000 Скачать руководство пользователя страница 26

26

Exterior Projection 1000 User Manual

Effects

Strobe / shutter

The strobe / shutter effect provides instant open and blackout as well as variable speed regular
and random strobe effects.

Electronic dimming

Overall intensity can be adjusted 0-100%. 16-bit dimming resolution is available using two DMX
channels.

CMY color mixing

CMY color mixing available on three DMX channels allows fine color adjustment.

Color wheel

The color wheel contains the 7 dichroic color filters listed below plus an open (white) position.

Colors can be selected in full position steps or continuously scrolled for split colors. The color
wheel can be rotated with variable speed and direction. It can also be set to display random colors
at slow, medium and fast speeds. The color wheel is shown below viewed from the LED side (rear
of the fixture):

Color wheel

Slot 1: Deep Red Slot 5: Orange

Slot 2: Light Blue

Slot 6: CTB

Slot 3: Primary Green

Slot 7: Violet

Slot 4: CTO

As an alternative to the above colors, Martin can supply custom color filters made to special order.
Please consult your Martin supplier for details.

«
...
24
25
26
27
28
...
»

Содержание Martin Exterior Projection 1000





























































Отзывы:

Нет отзывов