manualshive.com logo in svg

Harman Martin Exterior Projection 1000, Руководство пользователя, Страница: 25 / 60

Поделиться
Скачать
Harman Martin Exterior Projection 1000 Скачать руководство пользователя страница 25

 

 

Exterior Projection 1000 User Manual 

25 

•

  BLACK OUT (default): Fixture blacks out. 

-  If the fixture is set to MASTER and it does not receive a control signal, it will black out until 

it receives a control signal. 

-  If the fixture is set to SLAVE, it will always black out if it does not receive a control signal.   

The three options listed above also determine the fixture’s behavior if the fixture is receiving a 
control signal but that signal is suddenly lost. 

To set a fixture’s offline mode behavior: 

1.  Access the control menu and scroll to FIXTURE CONFIG. Press ENTER.   

2.  Scroll to MASTER/SLAVE and press ENTER. If you are going to set the fixture to RUN SHOW 

or DMX LAST STATE, scroll to MASTER and press ENTER to confirm. Press MENU to go 
back up one level. 

3.  Scroll to OFFLINE MODE and press ENTER. Press UP or DOWN to select RUN SHOW, DMX 

LAST STATE or BLACK OUT. Press ENTER to confirm. 

Setting effect offsets   

You should normally never need to change the Fixture Offsets setting. We recommend that you 
change the setting with guidance from Martin Service only. 

You can adjust the home position of each effect by setting an offset in the FIXTURE OFFSET 
menu. Adjustments are held in memory when the fixture is powered off and on.   

Offsets can be used to match multiple fixtures after they have been installed (if precise gobo 
alignment is required, for example). 

To reduce the risk of unauthorized tampering with the fixture, you must enter the user password 
(factory default = 123) before you can access the FIXTURE OFFSET menu.   

Setup via RDM   

The Exterior Projection 1000 is compatible with RDM (Remote Device Management). Using an 
RDM-compliant DMX controller, you can communicate with all the fixtures on a data link without 
needing to access the fixture’s control panels or connect to each fixture individually. RDM lets you 
set the DMX addresses of all the fixtures on the link, carry out basic fixture configuration and 
retrieve basic fixture data.   

See Remote Device Management (RDM) on page 43. 

 

 

Содержание Martin Exterior Projection 1000





























































Отзывы:

Нет отзывов