Guangzhou ZHIYUAN Electronics PA5000 Series Скачать руководство пользователя страница 93

Страница: 93 / 98

Date: 2016/12/08

User Manual

V1.00

Guangzhou ZHIYUAN Electronics Co., Ltd.

PA5000 Series Power Analyzer Start Guide

Measurement modes

Description

Flicker Mode

This mode performs voltage fluctuation and flicker measurement in

accordance with IEC61000-3-3 and IEC61000-4-15 international

standards.

FFT Mode

This mode can show the power spectrum of the input signal through

FFT (Fast Fourier Transform). Please use this mode to view the

frequency details of an input signal.

Cycle Mode

This mode can measure voltage, current, power and other

parameters of each AC input signal cycle.

8.5 Measurement Items

Table 8-17: Measurement items

Items

Symbols and Meanings

Voltage(V)

Urms: TRMS, Umn: ARV calibrated to

RMS

Udc: Linear Average Voltage, Urmn:

Rectified Mean Voltage

Uac: Voltage RMS that remove DC signal

Support for simultaneous

measurements,

peak

factor up to 300

Current(A)

Irms: TRMS, Imn: ARV calibrated to RMS

Idc: Linear Average Current, Irmn:

Rectified Mean Current

Iac: Current RMS that remove DC signal

Support for simultaneous

measurements, peak

factor up to 300

Active Power(W)

Apparent Power(VA)

Reactive Power(Var)

Power Factor

Phase Difference(°)

Frequency(Hz)

fU(FreqU): voltage frequency, fI(FreqI): current frequency

Maximum and

Minimum Voltage (V)

U+pk: maximum voltage, U-pk: minimum voltage

Maximum and

Minimum Current (A)

I+pk: maximum current, I-pk: minimum current

Peak Factor

CfU voltage peak factor, CfI current peak factor

Corrected Power (W)

Pc (applicable standards: IEC76-1(1976), IEEE C57.12.90-1993,

IEC76-1(1993))

Efficiency

Measurement of efficiency

Содержание PA5000 Series



































































































Результаты поиска

Содержание PA5000 Series

Отзывы:

Похожие инструкции для PA5000 Series

Бренды по названию

Популярные бренды

Guangzhou ZHIYUAN Electronics PA5000 Series, Руководство пользователя

Результаты поиска

Содержание PA5000 Series

Отзывы:

Похожие инструкции для PA5000 Series

Бренды по названию

Популярные бренды