Guangzhou ZHIYUAN Electronics PA5000 Series Скачать руководство пользователя страница 16

Страница: 16 / 98

Date: 2016/12/08

User Manual

V1.00

Guangzhou ZHIYUAN Electronics Co., Ltd.

PA5000 Series Power Analyzer Start Guide

Measurement

Functions

wiring units

Voltage

Voltage mean

UΣ

（

UrmsΣ, UmnΣ, UdcΣ, UrmnΣ, UacΣ

）

Current

Current mean

IΣ

（

IrmsΣ, ImnΣ, IdcΣ, IrmnΣ, IacΣ

）

Efficiency

PΣ

(sum of active power),

SΣ

(sum of apparent power),

QΣ

(sum

of reactive power),

λΣ

(average of power factor),

PcΣ

(sum of

corrected power)

Others

φΣ

(average of phase difference)

User-defined

functions

User-defined measurement functions (F1~F20)

Notes:

[1] Urms and Irms are true voltage and current rms value respectively. Each

instantaneous value in one period is squared and the result is averaged, then the resulting average

value is squared again. The equations are shown in Appendix B.

[2] Umn/Imn is the rectified mean value calibrated to the rms value. One period of the voltage

or current is rectified and the resulting average is multiplied by the factor that would yield the true

rms value if the applied signal were a sine wave. The factor is different from the value obtained in

RMS mode when distorted waves or DC waves are measured. The equations are shown in

Appendix B.

[3] Udc/Idc is defined as the average of one period of the voltage/current. This mode is useful

for determining the average value of a DC input signal or the value of a DC signal that is

superimposed on an AC signal.

[4] Urmn/Irmn is the rectified mean voltage/current. One period of the voltage or current is

rectified and the resulting average is obtained.

[5] Crest factor is defined as the ratio of the waveform peak value to the rms value.

[6] Waveform factor is defined as the ratio of the waveform rms value to the rectified mean

value.

PA5000 power analyzer can also use digital filtering to achieve an averaging process

when calculating the measured voltage or current values.

2.3 Operating Mode

The power analyzer includes several operating modes.



Normal Mode

. This mode is used to measure voltage, current, torque, speed,

power, and implement integral operation and waveform calculation.



Normal Measurement and Analysis Mode

. In this mode, the measured data

saved in the normal mode are replayed and analyzed so that users can observe

and analyze them conveniently.



Harmonics Mode

. Harmonics measurement can be performed on a signal with

0.5Hz~5kHz fundamental frequency.



IEC Harmonics Mode

. In this mode, users are allowed to perform harmonics

measurement conforming to the international standard IEC61000-3-2 and

IEC61000-4-7.



Voltage Fluctuation and Flicker Mode

. This mode allows users to perform

voltage fluctuation and flicker measurements conforming to IEC61000-3-3 and

IEC61000-4-15. Users can also set measurement conditions themselves and

then create a report of measurement results.

Содержание PA5000 Series



































































































Результаты поиска

Содержание PA5000 Series

Отзывы:

Похожие инструкции для PA5000 Series

Бренды по названию

Популярные бренды

Guangzhou ZHIYUAN Electronics PA5000 Series, Руководство пользователя

Результаты поиска

Содержание PA5000 Series

Отзывы:

Похожие инструкции для PA5000 Series

Бренды по названию

Популярные бренды