Grunbeck GENO-OSMO-X Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 76

background image

Reverse osmosis system

GENO-OSMO-X

Order no. 134 750 927-inter Edited by: phar/mrie G:\BA-750927-inter_134_GENO-OSMO_X.docx

66

Continuation table G-2: Troubleshooting

This is what you observe This is the cause

This is what to do

E103:
Text displayed at prog.
fault signal input

Signal is pending at the pro-
grammable fault signal input.
The reaction is programmed
to "error".

Remedy the cause of the pend-
ing signal.

Correct the programming of the
system reaction, if necessary
(refer to chapter F-4.2).

E104:
Error GENO-tronic

Operating element of the con-
trol unit defective.

Notify Grünbeck’s technical cus-
tomer service/authorised service
company.

E107.
Error
temperature sensor

Temperature sensor of the
permeate conductivity meas-
uring cell defective or short-
circuit at the conductivity
measuring cell

Notify Grünbeck’s technical cus-
tomer service/authorised service
company.

E108:
Error HP pump
RO1P2

Frequency converter of high-
pressure pump signals an er-
ror.

Flip the GENO-OSMO-X control
unit towards the front. Report
the error message of the fre-
quency converter to Grünbeck’s
technical customer service/au-
thorised service company.

E110:
R01V1 does not close

V1 does not close, probably
due to impurities or a defec-
tive valve.

Clean R01V1. Replace solenoid
valve.

E111:
Membrane degassing

Air flow is too low.

Check compressed air supply.

E113:
EH (water softener)
Error power failure

Power failure > 5 minutes.

If the power failure took longer,
start a manual regeneration to
be on the safe side. The water
flowing through the system in
the meantime, was not regis-
tered and the exchanger in oper-
ation might be overrun.

E114:
EH (water softener)
Error valve motor

The next step positon at the
control valve was not reached
within the required time.

If the error occurs again within 5
minutes after it was
acknowledged, notify
Grünbeck’s technical customer
service/authorised service com-
pany.

E116:
Error hard water

While one exchanger tank
has not yet been regener-
ated, the other is already ex-
hausted.

The error will acknowledge itself
as soon as a regenerated ex-
changer tank is available again.

«
...
66
67
68
69
70
...
»

Содержание GENO-OSMO-X













































































Отзывы:

Нет отзывов

Похожие инструкции для GENO-OSMO-X

Feeder/Deliming System EV9797-20

Бренд: Everpure Страницы: 2

Бренд: Rain Bird Страницы: 2

Traveler TR Series

Бренд: Rain Bird Страницы: 6

Бренд: ROSEDALE Страницы: 6

PROPLUS DI System

Бренд: SpectraPure Страницы: 24

Бренд: Miele Страницы: 52

Бренд: Miele Страницы: 48

Бренд: Miele Страницы: 36

Бренд: Miele Страницы: 31

Бренд: Miele Страницы: 36

Plug & Pure APST 000

Бренд: Miele Страницы: 112

Бренд: Miele Страницы: 48

Бренд: Miele Страницы: 36

Бренд: A.O. Smith Страницы: 20

Бренд: Lakos Страницы: 17

Бренд: LAMA Страницы: 24

Бренд: Xsential Страницы: 7

Бренд: Toro Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды