background image

Reverse osmosis system 

GENO-OSMO-X  

 

 

 

 

 

 

Order no. 134 750 927-inter   Edited by: phar/mrie  G:\BA-750927-inter_134_GENO-OSMO_X.docx 

52 

Parameters 

 

Factory 

setting 

Setting  

range 

Comment 

Input logic 
Error 
empty signal 
RO1CL.2 (*) 

 

NOC 

NOC/ 

NCC 

Contact type suction lance 
dosing pump RO1 P2 termi-
nals 63/64 (empty signal) 
resp. 63/65 (pre-warning): 

NOC

 = open contact means 

level has been undershot 

NCC

 = closed contact means 

level has been undershot 

Input logic 
Pre-warning  
RO1CL1 (*) 

 

NOC 

NOC/ 

NCC 

Input logic 
Residual hardness 
NX1CQ1(*) 

 

NOC 

NOC/ 

NCC 

Contact type alarm + limit 
value terminals 66/67 from 
monitoring device for residual 
hardness: 

NOC

 = Contact opens in case 

of power failure, malfunction or 
if the limit value is exceeded 

NCC

 = Contact is closed in 

case of alarm or if the limit 
value is exceeded. 

Input logic  
Level  
BB1CL1 … CL4  

 

CL1: NCC 

 

CL2…4: 

NOC 

NOC/ 

NCC 

The topmost level is declared 
as NCC by the factory, so that 
an error in the filling level 
measurement can be detected. 

NOC

 = contact open means 

level has been undershot 

NCC

 = contact closed means 

level has been undershot 

Input logic  
Programmable fault 
signal input 

 

NOC 

NOC/ 

NCC 

Input logic terminals 60/61: 

Input logic 
Error 
empty signal  
RO1CL4 (*) 

 

NOC 

NOC/ 

NCC 

Contact type suction lance 
dosing pump RO1P3 termi-
nals 50/62 (empty signal) 
resp. 50/51 (pre-warning): 

NOC

 = contact open means 

level has been undershot 

NCC

 = contact closed means 

level has been undershot 

Input logic 
Signal 
pre-warning  
RO1CL3(*) 

 

NOC 

NOC/ 

NCC 

Input logic  
Overpressure switch 
RO1 CP3 

 

NCC 

NOC/ 

NCC 

Contact type terminals 58/59: 

NOC

 = too high system pres-

sure closes contact 

NCC

 = too high system pres-

sure opens contact 

Solenoid valve out-
puts 

 

intermittend 

intermittend/ 

constant 

Applies to all valve outputs. 

Intermittend

 = valve output 

with timed pulses. 

Constant

 = valve output with 

constant pulses. 

Содержание GENO-OSMO-X













































































Отзывы: