GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 106

Страница: 106 / 118

2019-03-14

Table of Contents Index

195-067M

Great Plains Manufacturing, Inc.

Table of Contents Index

103

Appendix

Specifications and Capacities

3S-4000HD-7806

3S-4000HD-6375

3S-4000HD-4810

Row Count

Row Spacing

6 in. (15.2 cm)

7.5 in. (19.1 cm)

10 in. (25.4 cm)

Main Seed Box Capacity

129.6 bushels (4567 liters)

Tractor Requirements

180 hp minimum

Weight, standard HD model

a. See page 30 for additional weight data.

18136 lbs (8226 kg)

18102 lbs (8211 kg)

18071 lbs (8197 kg)

Weight, standard HDF model

23028 lbs (10446 kg)

22966 lbs (10417 kg)

22905 lbs (10389 kg)

Down-Force per Row

130-209 lbs

(59-95 kg)

135-240 lbs

(61-109 kg)

144-291 lbs

(65-132 kg)

Hydraulic Circuits

3 circuits required, load-sensitive or closed-center 15 to 30 gpm at 2300 psi

Optional kits are available for two-circuit, and open center.

Hitch Load

4800 lbs (2177 kg) folded in maximum loaded configuration

Caution:

negative tongue weight when raised and unfolded

Transport Width

15 feet (4.6 meters)

Operating Width

40 feet (12.2 meters)

Swath

480.0 in.

(1.219m)

476.5 in.

(1.21m)

475.0 in.

(1.207m)

Height

7 feet 4 inches (224 cm)

Length

34 feet 8 inches (10.6 meters)

Tire Sizes

Gauge Wheels: 265/70B16.5 NHS skid steer

Transport: 395/55B16.5 NHS skid steer

Tire Inflation Chart

Tire Warranty Information

Tire Size

Inflation

All tires are warranted by the original manufacturer of

the tire or wheel assembly. Tire warranty information is

found online at the manufacturer’s websites listed

below. For assistance or information, contact your

nearest Authorized Farm Tire Retailer.
Manufacturer

Web site

Firestone

www.firestoneag.com

Gleason

www.gleasonwheel.com

Titan

www.titan-intl.com

265/70B16.5 NHS Skid Steer

60 psi

(413 kPa)

395/55B16.5 NHS Skid Steer

60 psi

(413 kPa)

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 106 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: