GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 22

Страница: 22 / 118

Great Plains Manufacturing, Inc.

Table of Contents Index

Preparation and Setup

2019-03-14

Table of Contents Index

195-067M

Electrical Connections

Refer to Figure 7

Plug drill electrical lead into tractor seven-pin connector.

If your tractor is not equipped with a seven-pin

connector, contact your dealer for installation.

Refer to Figure 8 (connector styles and pin count vary with

monitor vintage - current Loup style shown)

If the drill is equipped with the optional shaft monitor,

mate the connector for the cab display.
See “

Shaft Monitor

” on page 101 for ordering

information.

Refer to Figure 9

If the drill is equipped with the point row option, mate the

connector for the cab control.
See “

Point Row Clutch

” on page 99 for ordering

information.

Figure 7

Lighting Connector

26467

Figure 8

Shaft Monitor Connector

34222

Figure 9

Point-Row Connector

26469

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 22 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: