GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 26

Страница: 26 / 118

Great Plains Manufacturing, Inc.

Table of Contents Index

Preparation and Setup

2019-03-14

Table of Contents Index

195-067M

Refer to Figure 12 on page 22 and Figure 13 at right

4. Release locking discs

on down-pressure valves.

Adjust knobs

on pressure-control valves for

opener down pressure so gauges

are at 2100 psi.

5. While watching gauges on drill, slowly turn knob on

bypass valve counterclockwise. Adjust bypass valve

just until needles on gauges begin to move down

from 2100 psi. Lock bypass valve at this setting.

(See also note below.)

6. Re-adjust pressure-control valves on drill to desired

opener down pressure as explained under

See “

Opener Frame Down-Force

” on page 58.

Note: The higher the bypass pressure, the greater the

potential for oil heating and premature tractor

damage. At the same time, for proper opener

operation the bypass valve must be set at least

300 psi above the opener down-pressure setting

when the tractor is at one-half throttle. Therefore,

you should set the bypass valve as low as possible

while staying at least 300 psi above the opener

down pressure setting.

While 2100 psi is a good starting point for setting the

bypass valve, if you consistently operate the drill with low

opener down pressure you can set the bypass valve

below 2100 psi. If you consistently operate the drill with

very high opener down pressure, you may need a

bypass-valve setting above 2100 psi.

Scraper Installation

Optional disk scrapers are not factory installed. To install

them in the field:
1. Remove one or both disk blades to gain safe access

to the mount. Note the position of bushings and

spacers for correct re-assembly (page 63).

Refer to Figure 14

2. Position the inside scraper mount

to the rear of

the seed firmer mount

on the opener weldment.

Secure it with two HHCS



-16



1in hex head bolts,

lock washers and nuts. Insert the bolts from the front.

3. Position the scraper blade

below and behind the

inside scraper mount

, with the notch on top to

machine right.

Secure it loosely with one RHSNB



-16



1 round

head square neck bolt, flat washer, lock washer and

nut.

4. Re-mount the removed disk blade.
5. Adjust the scraper blade per “

Disk Scraper

Adjustments

” on page 63.

Figure 13

Down Pressure for Bypass

26471

Figure 14

Scraper Installation

26460

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 26 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: