GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 77

Страница: 77 / 118

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

195-067M

Table of Contents Index

2019-03-14

In-Line Filters

If the raising or lowering times of the openers slow

noticeably, check the in-line filters and clean if needed.

Refer to Figure 81

Two filters are located on one each of the down-pressure

adjustment valves. If the Point Row option is installed,

another filter is located on the third adjustment valve.

Refer to Figure 82

To disassemble unscrew end cap of filter. Remove top

retaining washer and screen.
Clean filter screen with solvent and compressed air, or

replace if needed.
When reassembling put screen into filter. Place retaining

washer on top of filter and screw on end cap.

Figure 81

In-Line Filter Locations

22968

Figure 82

In-Line Filter

25187

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 77 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: