GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 27

Страница: 27 / 118

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

195-067M

Table of Contents Index

2019-03-14

Marker Setup

Refer to Figure 15

Markers are field-installed, but usually do not have their

extension length precisely set. The drill must be

leveled per “

Leveling the 3S-4000HD/HDF Drill

” on

page 80, and marker(s) must be in correct working order

per “

Marker Maintenance

” on page 86.

Row unit centerline stations on 3S-4000HD/HDF drills

are symmetrical about machine center, so left and right

extensions are normally identical, for both opposing and

concentric passes.
Set the initial length of the marker(s) as follows:
1. Lower drill and openers to field position (“

Raising

and Lowering Openers

” on page 26).

2. Extend a marker on one side. Pull forward several

feet to leave a mark.

3. Sighting parallel to the main tool bar, measure from

the centerline of the outside row unit to the mark.

4. Adjust the marker extension

so that the mark is

one half

the span

plus one row unit spacing

“

Marker Adjustments

” on page 66 for setting

marker extension.

5. Pull forward several feet, and re-measure to verify

any adjustment. Validate the mark by making a pass

to one or both sides.

6. Fold marker. Extend other side and adjust.
Note: If field conditions require inverting the marker disk

(page 67), the mark moves, and the extension

needs to be re-measured and reset. Marking also

changes slightly if the opener frame trunnion

position is changed (page 60).

Models

Spacing

Extension

3S-4000HD-4810

3S4000HDF-4810

10 inch

245.0in

(622.3cm)

3S-4000HD-6375

3S4000HDF-6375

7.5 inch

242.0in

(614.7cm)

3S-4000HD-7806

3S4000HDF-7806

6 inch

240.5in

(610.9cm)

Figure 15

Marker Extension

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 27 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: